Q. 25. A conical draft tube having diameter at the top as 2m and pressure head at 7mof water (vacuum), discharges water at the outlet with a velocity 1.2m/sec at the rateof 25 m³/sec. If atmospheric pressure head is 10.3 m of water and lanes between theinlet and outlet of the draft-tubes are negligible. Find the length of draft-tubes immersedin water. Total length of tube is 5m.

Answered: Image /qna-images/answer/27b94c75-808b-4c08-be98-7bdd95abd92f.jpg

. 25. A conical draft tube having diameter at the top as 2m and pressur fwater (vacuum), discharges water at the outlet with a velocity 1.2m/se f 25 m³/sec. If atmospheric pressure head is 10.3 m of water and lanes let and outlet of the draft-tubes are negligible. Find the length of draft-tul M wil

. 25. A conical draft tube having diameter at the top as 2m and pressur fwater (vacuum), discharges water at the outlet with a velocity 1.2m/se f 25 m³/sec. If atmospheric pressure head is 10.3 m of water and lanes let and outlet of the draft-tubes are negligible. Find the length of draft-tul M wil

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. Water flows through a horizontal nozzle, as shown. At the nozzle inlet the diameter is 6in. At the nozzle outlet, where the pressure is atmospheric, the diameter is 2in. Determine the pressure head at the nozzle inlet required to produce a jet velocity of 40ft/sec. Neglect friction loss an assume incompressible flow. A1 A2 1 2.
5.) A horizontal pipe gradually reduces from 250 mm to 150 mm diameter section, the pressures are 90 kPa and 70 kPa, respectively. If the flow rate is 15 L/s of water, compute the head lost (m) between the two sections.
V,=5m/s Water enters a 120- horizontal reducing pipe with a velocity of 5m/s and a pressure of 78.48 kNm2. If the diameters atthe entrance and exit sections are 30 cm and 20 cm respecí vely and assuming no degradation of energy within the pipe, find: 60 15. The flow rate passing through the pipe is a) 0.09 m³/s b) 0.1571 m/s c) 0.3534 m/s d) 1.5 m/s 16. The velocity of flow at the exit is a) 11.25 m/s b) 1.77 m/s c) 5.0 m/s d) 25.0m/s 17. The pressure at the exit of the pipe is a) 27.7 kN/m? b) 78.48 kN/m? c) 15.2 kN/m2 d) 81.3 kNm2 18. The horizontal component of the force on the pipe from the water is b) 7315 N a) 7750.7 N c) 5549N d) 9739 N 19. The vertical component of the force on the pipe from the water on pipe is b)4216 N a) 2701 N c) 3459 N d) 5673 N 20. The direction of the resultant force relative to the horizontal direction is b) 23.4. a) 66.6. c) 30. d) 70-
1. Water is flowing with velocity 2.8 m/s in an 80 mm diameter half opened gate valve. Determine the head loss through this valve. (Ans.: 2.398 m)
solution only
40 L/s of 20C water (ν = 1.007*10^(-6) m^2/s). Flows through 1,200 ft of6-in diameter new steel pipe with ks = 0.0002 ft. The friction loss must be:
Q2. Flowrate of water through bend pipe (90°) is 0.21 m/s. The pipe diameter at the inlet is 150 mm and the outlet diameter is 75 mm. The outlet is higher than the inlet by 2 m. Frictional losses in the pipe is equal a loss factor of 0.5 applied to the inlet velocity head. The pressure head at the inlet is 8.6 m and the volume of water in the bend is 0.6 m?. Calculate the resultant force and its direction.
1. (Flow rate problem) Water at 50°F flowing through 80 ft of 4-in-diameter average cast-iron pipe (e = 0.00085 ft) causes a friction head loss of 0.27 ft. Find the flow rate.
A 4-in.-diameter pipe carries 300 gal/min of water at a pressure of 20 psi. Determine (a) The velocity head (ft); and (b) The total head (ft) with reference to a datum plane 20 ft below the pipe.
A flow of water of 100 lt/sec flowing through rectangular tube of width 600 mm and having adjustable bottom slope with C = 56. Find the bottom slope required for uniform flow of depth 300 mm. Also, determine the convenience of fume.
Subject : Fluid mechanics Give me all answers.. Urgent
A flow of water of 100 lt/sec flowing through rectangular tube of width 600 mm and having adjustable bottom slope with C = 56. Find the bottom slope required for uniform flow of depth 300 mm. Also, determine the convience of fume.