HR-EKG_Assignment_1 (1)

Instrumentation & Measurements This homework measures your capability to design/analyze various components/variables of ameasurement system based on what you have studied. Question is Attached in image. Thank you.

Investigate, and select appropriate sensors for the specified system.

Sensor systems for obstacle detection and avoidance in mobile robots. • Produce a written report documenting: the choice of sensors, sensor evaluation, the developed processor/measurement system, and overall system performance.

Select atleast two testing devices from among the categories (you may go beyond two). Discuss its application and methods of use. a. testing for speed (Tachometer), b. Testing of Air Consumption (Air-box method/viscous-flow meter), c. testing of exhaust smoke (Bosch/Hartridge/PHS), d. testing of exhaust emission (flame ionization detector/spectroscopic analyzers/gas chromatography) e. testing of torque (absorption dynamometer/transmission dynamometer).

The Weather Monitor. Your South American expedition splits into two groups: one that stays at home base, and yours that goes off to set up a sensor that will monitor precipitation, temperature, and sunlight through the upcoming winter. The sensor must link up to a central communications system at base camp that simultaneously uploads the data from numerous sensors to a satellite. In order to set up and calibrate the sensor, you will have to communicate with base camp to give them specific location information. Unfortunately, the group's communication and navigation equipment has dwindled to walkie-talkies and a compass due to a river-raft mishap, which means your group must not exceed the range of the walkie-talkies (3.0 miles). However, you do have a laser rangefinder to help you measure distances as you navigate with the compass. After a few hours of hiking, you find the perfect plateau on which to mount the sensor. You have carefully mapped your path from base camp around lakes and…

Subject: Air Pollution Formation and Control Do not just copy and paster other online answers

A. A student establishes the time constant of a temperature sensor by first holding it immersed in hot water and then suddenly removing it and holding it immersed in cold water. Several other students perform the same test with similar sensors. Overall, their results are inconsistent, with estimated time constants differing by as much as a factor of 1.2. Offer suggestions about why this might happen. Hint: Try this yourself and think about control of test conditions. B. Which would you expect to be better suited to measure a time-dependent temperature, a thermal sensor (e.g., a thermocouple) having a small diameter spherical bead or one having a large diameter spherical bead? Why?

I Blackboard @ Texas Tech Uni x Bb MasteringEngineering - Spri x E MasteringEngineering Maste X C Suppose That H = 3.8 M . (Fi x X Mathway | Calculus Problem x y! how to take a full page scree A session.masteringengineering.com/myct/itemView?assignmentProblemID=12360392&offset=next ABP O Tp E G KAssignment #3 Fundamental Problem 2.29 5 of 6 > I Review Part A Find the magnitude of the projected component of the force along the pipe AO. (Figure 1) Express your answer to three significant figures and include the appropriate units. µA FAO = Value Units Submit Request Answer Figure 4 m F = 400 N 6 m 5 m B 4 m 10:31 PM O Type here to search 2/7/2021

QUESTION 2 SOALAN 2 a) The DP Transmitter device is used to measure level as an inferential measurement. When installing the DP Transmitter in an open tank at HP tapping point at 0%, the lower range values (LRV) and upper range values (URV) for the transmitter must be determined in order to properly register 0% at the LRV and 100% at the URV liquid level. By referring to Figure 2, calculate the calibrated range with specific gravity, SG is 1.1 and height, H of the tank is 100mm. Peranti Pemancar DP digunakan untuk mengukur paras sebagai ukuran taabir. Apabila memasang Pemancar DP di tangki yang terbuka di HP titik tirus pada 0%, nilai julat yang lebih rendah (LRV) dan nilai julat atas (URV) untuk pemancar mesti ditentukan untuk daftarkan betul pada 0% LRV dan 100% URV. Dengan merujuk Rajah 2, hitungkan julat yang dikalibrasi dengan graviti spesifik, S.G adalah 1.1 dan ketinggian, H tangki adalah 100mm. Tank open to Atmosphere Махт. Level Liquid DP Transmitter Vented to Atmosphere Min.…

Pressurized eyes Our eyes need a certain amount of internal pressure in order to work properly, with the normal range being between 10 and 20 mm of mercury. The pressure is determined by a balance between the fluid entering and leaving the eye. If the pressure is above the normal level, damage may occur to the optic nerve where it leaves the eye, leading to a loss of the visual field termed glaucoma. Measurement of the pressure within the eye can be done by several different noninvasive types of instruments, all of which measure the slight deformation of the eyeball when a force is put on it. Some methods use a physical probe that makes contact with the front of the eye, applies a known force, and measures the deformation. One non-contact method uses a calibrated “puff” of air that is blown against the eye. The stagnation pressure resulting from the air blowing against the eyeball causes a slight deformation, the magnitude of which is correlated with the pressure within the eyeball.…

You’re testing a system that involves a fan, water pump, and compressor. The components are turned ON in sequence and sensor readings are taken, as per a written protocol that you’re following. The system is running as expected after the fan and water pump are turned ON. However, when you turn ON the compressor, it runs for about thirty seconds then stops, consistently. Swapping out the compressor for a different one seems to solve the problem. What could have been the issue with the bad compressor?

Please do not copy other's work and do not use ChatGPT or Gpt4,i will be very very very appreciate!!! Thanks a lot!!!!!

You are assigned as the head of the engineering team to work on selecting the right-sized blower that will go on your new line of hybrid vehicles.The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement. Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1,2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and the blower configuration.You can only use the following parameters: