Lab 1-Anatomical Structures and Positions

Could you please explain where and what is tight side and also how to find 5-9

I need help solving this problem.

I need help answering problems 4, 5, and 6 pertaining to the print provided in the attachment.

I need help answering questions 7, 8, and 9 pertaining to the print attached.

I need help answering questions 4, 5, and 6 pertaining to the print provided below.

I can't find the symbols for the blank ones

Match the following statements with the term that best describes each statement. hooks law creep impact strength proportional limit fatigue elastic

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

I need help with problems 1, 2, and 3 pertaining to the print provided below.

I need help solving problems 10, 11, and 12 pertaining to the print provided.

I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.

Problem 3: Insulation To=1 Toowwww Steam Tx2 T₂ T3 www www R₁ R₁ R₂ www.T R₂ Steam at T1 = 320 °C flows in a cast iron pipe (k= 80 W/m. °C) whose inner and outer diameters are 5 cm = 0.05 m and D₂ = 5.5 cm = 0.055 m, respectively. The pipe is covered with 3-cm-thick glass wool insulation with k = 0.05 W/m. °C. Heat is lost to surroundings at T2 = 5 °C by natural convection and radiation, with a combined heat transfer coefficient of h₂ = 18 W/m². °C. Taking the heat transfer coefficient inside the pipe to be h₁ = 60 W/m². °C, determine the temperature drops across the pipe and the insulation. The determination is based on a unit length of the pipe (L = 1 m). Assumptions 1. Heat transfer is one-dimensional since there is no indication of any change with time. 2. Heat transfer is one-dimensional since there is thermal symmetry about the centreline and no variation in the axial direction. 3. Thermal conductivities are constant. 4. The thermal contact resistant at the interface is…

The question and data are in pictures. Please answer properly with each steps and explanation. Best of luck. Thank you so much in advance.

I need answers to parts 4, 5, and 6, pertaining to the print provided.

Hartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectors

I need answers to questions 4, 5, and 6 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

Hello, so i have attached two images. the first image is the quetions, i need part b) answered if possible. i have attached my findings to part a) to add to the little information we know to help with part b if needed. Thnks

I need answers for problems 1, 2, and 3 pertaining to the print provided.

The first photo is the question, where the 2nd shows some problem solving strategies

As shown in figure a Pepsi can and a plastic Pepsi bottle. Describe how they were manufactured

Match the following statements with the term that best describes each statement. (Enter Number ONLY) 1) Hooke's Law 2) Creep 3) Impact Strength 4) Proportional Limit 5) Fatigue 6) Elastic The tendency of a solid material to move slowly or deform permanently under the influence of mechanical stresses below the yield strength of the material. The behavior of materials that deform when loaded but return to their original shape after the load is removed. The linear relationship between stress and strain in the elastic region below the proportional limit. The phenomenon where cracks propagate under loads less than the yield stress due to cyclic loading. The material property determined using the Charpy or Izod test. The point at which the stress vs strain becomes non-linear in an elastic material,

I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

I need parts 4, 5, and 6 answered pertaining to the print provided.

Q1 please

Constants | Periodic Table Part A A 71 kg man's arm, including the hand, can be modeled as a 79-cm-long uniform cylinder with a mass of 3.5 kg In raising both his arms, from hanging down to straight up, by how much does he raise his center of gravity? Express your answer with the appropriate units. ? h = Value Units Submit Request Answer