Module 7- Inspections and Maintenance Quiz

please help solve A-F. thank you You are an engineer working on a project and your prototype has failed prematurely. You question whether or not a key component of the prototype was manufactured with the correct material. There are two way to check for the material properties. The first way is to have a material certification done to confirm the exact material composition. This will take some time. The second method to confirm the material properties is to make an ASTM test sample and test for the material properties. This tensile test was completed on a test sample with an initial diameter of .501” and an initial length of 2”. The Load-Deflection data for this tensile test is below. Use this data to answer the first set of questions on the Final Exam in eLearning. A. Determine the Ultimate Tensile Strength B. Determine the 0.2% Offset Yield Strength C. Determine the value of the Proportional Limit D. Determine the Modulus of Elasticity E. Determine the Strain at Yield F. Calculate %…

I need parts 8, 9, and 10 answered. Number 1 is an example of how it should be answered. NOTE: Read the instructions, no where does it say any drawing is required. It is really frustrating when I wait all this time for an answer to a question and some tutor does even read the instructions and just declines it...its ridicilous.

Help!!! Answer all parts correctly!! Please

Help!!! Please answer part b correctly like part A. Please!!!!

Enginooring Mochanics: Sutca (1 Fint Scitester, Firt yoat, Academic yer 2020-2021 Deputtane of Civil Engnoeg Callege of Engincenng Lasenaty ut Mis Cm link on Miodle Instructor: Dr. Murtada Abass Mid-term Examination of E113 1 year 2020-2021 Date: March 5, 2021 Time: 20 Minutes Answer one question only which is assigned for you only Your Question is assigned via Mloodle in Ouizzes Section Your answer to the question will be submitted via Zoom Question: Determine the reactions of the truss shown in the Figure, 5 KN lom A جميلة محمد 15 کشيش lom IDM Page15

J 6

! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. At an intersection car B was traveling south and car A was traveling 30° north of east when they slammed into each other. Upon investigation, it was found that after the crash, the two cars got stuck and skidded off at an angle of 10° north of east. Each driver claimed that he was going at the speed limit of 50 km/h and that he tried to slow down, but couldn't avoid the crash because the other driver was going a lot faster. The masses of cars A and B were 1500 kg and 1200 kg, respectively. 10° 30° VR Determine the speed of the faster of the two cars if the slower car was traveling at the speed limit. The speed of the faster car was km/h.

Per Bartleby honor code only 3 subparts of a question can be answered per submission. I have submitted 10, 11, 12, and 13 previously. Please answer 14, 15, 16

Please answer the 4th question

I need problems 6 and 7 solved.  I got it solved on 2 different occasions and it is not worded correctly. NOTE: Problem 1 is an example of how it should be answered. Below are 2 seperate links to same question asked and once again it was not answered correctly. 1. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857 2. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/bd5390f0-3eb6-41ff-81e2-8675809dfab1

Please give me the answers for this i been looking at this for a hour and my head hurts

I need parts 1, 2, and 3 answered pertaining to the print provided. NOTE: If you refuse to answers all 3 parts and insist on wasting my question, then just leave it for someone else to answer. I've never had an issue until recently one single tutor just refuses to even read the instructions of the question and just denies it for a false reasons or drags on 1 part into multiple parts for no reason.

Help!!! Answer it correctly!!! Make sure you solve work on hand!!! Answer correctly Please!!!!!!!

Mech. Engg. Dept. 4th year 2022-2023 Solar Energy Spring course MEC364 Dr. Mahmoud U. Jasim Review/Recap Sheet Q1- Answer with true or false and rewrite the false statements completely in correct form, otherwise no mark will be put on the false statements. 1 2 To represent a location on earth surface you need to define its altitude and longitude angles. 3 Solar zenith and solar incidence angles have the same value for horizontal surface. At sunset time the value of solar altitude angle is maximum. 4 The angle which represents the inclination of a given surface is the zenith angle 5 6 7 8 When the absolute value of sun-wall azimuth angle exceeds 90' this means that the sun rays are reaching the receiving plane. The solar irradiance and the solar irradiation have the same physical meaning. In the case of clear sky weather, the beam solar irradiation on a horizontal surface is less than the diffused irradiation. The total solar radiation received by a tilted surface is the same as that…

I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

FINALS ASSIGNMENT IN ME 3215 COMBUSTION ENGINEERING PROBLEM 1: A Diesel engine overcome a friction of 200 HP and delivers 1000 BHP. Air consumption is 90 kg per minute. The Air/fuel ratio is 15 to 1. Find the following: 1. Indicated horsepower 2. The Mechanical efficiency 3. The Brake Specific Fuel Consumption PROBLEM 2: The brake thermal efficiency of a diesel engine is 30 percent. If the air to fuel ratio by weight is 20 and the calorific value of the fuel used is 41800 kJ/kg, what brake mean effective pressure may be expected at S.P. conditions (Standard Temperature and pressure means 15.6°C and 101.325 kPa, respectively)?

4

Solve all parts

I think understand the concept but I'm stuck on how allowance and tolerance are did. I wasn't sure if I was supposed to write separate numbers for allowance then the two for tolerance. Or am I supposed to use the number I get from allowance to calculate tolerance. I've read pages but feels like my brain is like not connecting the dots or I misread something.

I need answers for problems 13, 14, and 15 pertaining to the print provided.   NOTE: If you refuse to answers all 3 parts and insist on wasting my question by breaking down 1 simple question into 3 parts, then just leave it for someone else to answer. Thank you.

Don't use chatgpt will upvote

Help with this would be great, thanks!

LESSON: AUTODESK AUTOCAD Choose from the choices:

Statics Problem !!! Help me Part A , Part B , Part C!!!! Answer it this Problem Correctly!! Please give correct Solution

I need answers to questions 7, 8, and 9 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

please read everything properly... Take 3 4 5 hrs but solve full accurate drawing on bond paper don't use chat gpt etc okk