Week 4 Assignment

Can anyone help me with this question

A tension test was performed on a specimen having an original diameter of 11.5 mm and a gauge length of 50 mm. The data are listed in the table. Load (kN) Elongation (mm) 0 11.1 31.9 37.8 40.9 43.6 53.4 62.3 64.5 62.3 58.8 0 0.0175 0.0600 0.1020 0.1650 0.2490 1.0160 3.0480 6.3500 8.8900 11.9380 Plot the stress-strain diagram. Use a scale of 20 mm = 50 MPa and 20 mm = 0.05 mm/mm. Redraw the linear-elastic region, using the same stress scale but a strain scale of 20 mm = 0.001 mm/mm. From the diagram, determine approximately the modulus of elasticity. Express your answer to three significant figures and include the appropriate units. E 215 Submit Previous Answers Request Answer Part B μÀ X Incorrect; Try Again; 2 attempts remaining Tu = 530 Determine the ultimate stress. Express your answer to three significant figures and include the appropriate units. GPa μÅ Part C Submit Previous Answers Request Answer MPa | μA ? X Incorrect; Try Again; 2 attempts remaining of=479.15 Determine the…

A tension test was performed on a specimen having an original diameter of 13.7 mm and a gauge length of 50 mm. The data are listed in the table. Load (kN) Elongation (mm) 0 11.1 31.9 37.8 40.9 43.6 53.4 62.3 64.5 62.3 58.8 0 0.0175 0.0600 0.1020 0.1650 0.2490 1.0160 3.0480 6.3500 8.8900 11.9380 Plot the stress-strain diagram. Use a scale of 20 mm = 50 MPa and 20 mm = 0.05 mm/mm. Redraw the linear-elastic region, using the same stress scale but a strain scale of 20 mm = 0.001 mm/mm. From the diagram, determine approximately the modulus of elasticity. Express your answer to three significant figures and include the appropriate units. E = Submit Part B συ = Submit Part C ☐☐ μÅ of = Value Determine the ultimate stress. Express your answer to three significant figures and include the appropriate units. Request Answer μĂ Value Request Answer Units μĂ - Value Units Determine the fracture stress. Express your answer to three significant figures and include the appropriate units. ? Units ? ?

A tension test was performed on a steel specimen having an original diameter of 0.503 in. and gauge length of 2.00 in. The data is listed in the table below. (Figure 1) Figure Load (kip) Elongation (in.) 0 0 1.50 0.0005 4.60 0.0015 8.00 0.0025 11.00 11.80 11.80 12.00 16.60 20.00 21.50 19.50 18.50 0.0035 0.0050 0.0080 0.0200 0.0400 0.1000 0.2800 0.4000 0.4600 1 of 1 Part C Determine approximately the ultimate stress. Express your answer to two significant figures and include the appropriate units. Ju = Submit Part D OR= Submit μÅ Value Request Answer Determine approximately the rupture stress. Express your answer to two significant figures and include the appropriate units. Provide Feedback Value [ID] ? Request Answer Units Units ?

400 350 300 250 200 150 100 50 0.002 0.004 0.006 0.008 0.01 Strain Stress (MPa)

Please show handwritten solution

A tension test was performed on a specimen having an original diameter of 13.0 mm and a gauge length of 50 mm. Load (kN) Elongation (mm) 0 11.1 31.9 37.8 40.9 43.6 53.4 62.3 64.5 62.3 58.8 0 0.0175 0.0600 0.1020 0.1650 0.2490 1.0160 3.0480 6.3500 8.8900 11.9380 Using the data listed in the table, plot the stress-strain diagram. Use a scale of 20 mm = 50 MPa and 20 mm = 0.05 mm/mm. Part A From the diagram, determine approximately the modulus of toughness. Express your answer to three significant figures and include the appropriate units. U = Submit O μA Value Request Answer Units < Return to Assignment Provide Feedback ?

The following data were collected from a 10.16 mm-diameter test specimen of polyvinyl chloride (e, = 50.8 mm): Load (kN) AE (mm) Stress (MPa) Strain (mm/mm) O 0.0 O 0.00000 1.334 0.1895 16.45492 0.00373 32.90983 0.00748 2.668 0.38 4.003 0.603 49.37708 0.01187 5.34 0.813 65.869 0.016 6.67 1.168 82.27458 0.023 7.38 1.778 (maximum load) 91.03244 0.035 7.12 2.388 87.82534 0.047 6.316 3.048 (fracture) 77.90798 0.06 After fracture, the total length was 53.086 mm and the diameter was 9.982 mm. Plot the engineering stress strain curve and calculate (a) the 0.2% offset yield strength; (b) the tensile strength; (c) the modulus of elasticity: (d) the % elongation; (e) the % reduction in area; () the engineering stress at fracture

I want handwriteen and correct answer only don't do if u don't knowpls

can you make it computerized instead of handwritten

30. In a typical tension test a dog-bone shaped specimen is pulled in a machine. During the test, the force F needed to pull the specimen and the length L of a gauge section are measured. This data is used for plotting a stress-strain diagram of the material. Two definitions, engineering and true, exist for stress and strain. The engineering stress F de and strain e are defined by oe F %3D and A0 L-Lo where Lo and Ao are the initial gauge 6, = Lo length and the initial cross-sectional area of the specimen, respectively. The true stress o, and strain e are defined by o, 는는 and q %3D = In A0 Lo The following are measurements of force and gauge length from a ten- sion test with an aluminum specimen. The specimen has a round cross sec- tion with a radius of 0.25 in. (before the test). The initial gauge length is 0.5 in. Use the data to calculate and generate the engineering and true stress- strain curves, both on the same plot. Label the axes and use a legend to identify the curves. Units:…

I am testing how mesh sizes in abaqus affect the maximum stress found in the fillet section of a part which has load on either side of the fillet, how would I propose a method and perform a calculation to compare with the values from the model?

7. Calculate the minimum wall thickness between the inside diameter and datum feature B shown in the figure below. Datum B @ LMC: Ø -Ø minus I. D. @ LMC: minus Tolerance @ LMC: - Ø. = The wall thickness equals half of the differences in diameters = Ø2.500 .020 4.059 +.003 Ø2.000 .020 +0.0200 ABO B A Unless otherwise Specified: .XXX= .010 ANGLES = ± 1°