w6a1_whitneylane

Needs Complete typed solution with 100 % accuracy.

What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure Swing Adsorption Oxygen Generator (PSA) COMPs = Compressors POMPs = Pumps HEAT = Heat Exchanger PV = Flow Valves ST TANK = Storage Tank VENT = Vent DR = Drains PSV = Pressure Relief Valve In addition, what would be the possible problems that would require flexibility correction by adding expansion joints, spring supports, anchors and brackets?

In GD&T Coaxiality is that condition where the axes of two or more surfaces of revolution are _____________. There is a misconception that centerlines or the tolerance block control the ____________________ between two cylinders.

Complete PDS for a 3D modeling of a baby’s neck with trachea for surgical training procedure

Distilled water at 10deg C stands in a glass tube of 9.0 mm diameter at a height of 24.00 mm. What is the true static height in mm if the surface tesnsion is 0.0742 N/m.   a.24 mm b.27.4 mm c.20.6 mm d.3.4 mm

CHAPTER 5 : DIESEL ENGINE POWER PLANT A six cylinder, four-stroke CI engine is tested against a water brake dynamometer for which B.P = WN/17x10' in kW, where W is the brake load in newton and N is the speed of the engine in the r.p.m. The air consumption was measured by means of a sharp edged orifice. During the test following observersations were taken : • Bore • Stroke • Speed • Brake load Barometer reading = 10 cm = 14 cm = 2500 rpm = 480 N = 76 cm Hg • Orifice diameter • Co-efficient of discharge of orifice • Pressure drop across orifice • Room temperature Fuel Consumption = 3.3 cm = 0.62 = 14 cm of Hg = 25°C = 0.32 kg/min Calculate following : i. The volumetric efficiency The brake mean effective pressure ( b.m.e.p) The engine torque The brake specific fuel consumption ( b.s.f.c ) ii. iv.

A person is required to perform a lifting task. After conducting the analysis of the task shown below using the NIOSH lifting guidelines you determined that the task need to be redesigned to be acceptable. Unfortunately, the only factor that you can modify is the frequency of lifts per minute. What is the maximum number of lifts per minute that need to be used for this task so the NIOSH lifting guidelines are not exceeded?   ANSWER:  ________________

4

Which tool helps to categorise risks into three colour-coded zones representing major, moderate, and minor risks Risk Priority Number Risk assessment matrix Failure Mode and Effects Analysis O Severity Matrix

QUESTION 2 SOALAN 2 a) The DP Transmitter device is used to measure level as an inferential measurement. When installing the DP Transmitter in an open tank at HP tapping point at 0%, the lower range values (LRV) and upper range values (URV) for the transmitter must be determined in order to properly register 0% at the LRV and 100% at the URV liquid level. By referring to Figure 2, calculate the calibrated range with specific gravity, SG is 1.1 and height, H of the tank is 100mm. Peranti Pemancar DP digunakan untuk mengukur paras sebagai ukuran taabir. Apabila memasang Pemancar DP di tangki yang terbuka di HP titik tirus pada 0%, nilai julat yang lebih rendah (LRV) dan nilai julat atas (URV) untuk pemancar mesti ditentukan untuk daftarkan betul pada 0% LRV dan 100% URV. Dengan merujuk Rajah 2, hitungkan julat yang dikalibrasi dengan graviti spesifik, S.G adalah 1.1 dan ketinggian, H tangki adalah 100mm. Tank open to Atmosphere Махт. Level Liquid DP Transmitter Vented to Atmosphere Min.…

Do not provide handwritten solution,Maintain accuracy and quality in your answer,Take care of plagiarism,Answer completely,You will get up vote for sure.

Industrial Maint. What impact does a rigorous lubrication program have on a facility?