SCI 100 Module Six Activity Template (1)

I have an O Gauge track and would like to convert it into a “sensored” track. Additionally, I would like to connect that track to an ESP-WROOM-32 board that should flash an LED whenever the track detects a non-moving train. Please list all the components (and how many of each) needed. Also, what’s the procedure for connecting the components?

I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards on top of the train. Broadcast communication (which involves radio frequency, not Wi-Fi) would help communicate about the train's lateness to five other wooden trains on the same track. Local communication would help communicate to the train station about the train's lateness. I would also need radio frequency Tx-Rx Modules for discharging and undergoing the signal, and repeaters just in case the signal loses power due to long-distance traveling. My wooden train should be automated. It should run at 4 inches per second, keep a minimum distance of 30 seconds away from the other wooden trains, and make a 17-second-long stop every 500 seconds. What's the procedure to connect the components? What's the Arduino code (C++) for this project?

Please answer this diligently. Other answers in the internet seems wrong. Please help me understand and solve this problem. I'll give a like. Thanks! Ig2sc = __________; Isc = __________; MVAsc = __________

Centennial College - School of Engineering Technology - Toronto ELECTRONICS SHOP PRACTICES CHAPTER 7: SOLDERING TECHNIQUES 7,5 QUESTIONS 1. Which tools will you need for soldering? 2. What type of solder do we call the Eutectic Solder? 3. If the temperature is too high, the is bellow required, the solder joint will appear cold and silvery and will be of the contact may occur and circuit will not work. If the 4. A long and sharp will be of little use when soldering wires or 5. The iron should have a tip to prevent and should have a wattage rating of to Watts. 6. When soldering, apply heat solder will to both, the component lead and much more readily over the copper pad so that the 7. Keep the soldering iron tip and working surfaces wipe only before using and immediately. 8. Do not solder from a heated tip before off the iron. alternate applying the surface. 9. If tips become and wiping to being used. 10. Periodically. the tip from your tool and with a suitable cleaner for your skills.…

Series Circuit 4.(4) Location Voltage AIA2 Double-click to hide white space BIB2 - Lamp B Cic2 -- Lamp C Across Power Supply - (Entire Circuit) 5.(4a) How does the voltage across the lamps compare?. 6.(4b) How does the voltage of each lamp compare with the voltage of the power supply2 Describe how the voltage changes2 7.(6) Inited States) Focus MacBook Air 88 DII F3 F4 F5 F6 F7 F8 F9 F10 $ 4 6. 7 8. R T. Y U F G H J

Explain briefly about the the circuit diagram and explanation of the analysis of equations.

i need the answer quickly

1- Draw the complete circuit diagram that illustrates the experiment concept as in figure 5 by showing the pins number. Show the following in your plot (Arduino board, steppermotor coils and the driver circuit). Note: The drawing should be on paper and not with artificial intelligence, please.

Please send the answer by typing only. I don't want handwritten.  The subject is ( Electronic Circuits ) Q2) Mention the applications of FET.

As an electrical and electronic engineer, your manager has asked you to write a report for the attention of new employees, listing and describing the operation of safety devices that are commonly found offices and other industrial situations. The report should include all of the details in the task below.     Task   For the following application, list two electrical safety devices that can be used, and describe their operation:A Star delta starting induction motors

DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS   NOTE: Please solve in this way. Please have a good handwriting, some of the answers are not readable. Thank you! GIVEN. (Include symbols and units) ILLUSTRATION (Required). Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible FINAL ANSWERS must be rounded up to three decimal places with underlined twice

please answer all questions and give me a sample ansowers 1. What code sets standards for electrical installation work? 2. What authority enforces the requirements set by the NEC? 3. Does the NEC provide minimum or maximum standards? 4. What do the letters “UL” signify? 5. What section of the NEC states that all listed or labeled equipment shall be installed or used in accordance with any instructions included in the listing or labeling? 6. When the word “shall” appears in a NEC reference, it means that it (must)(may) be done. (Underline the correct word.) 7. What is the purpose of the NEC?

A computer's power supply converts mains AC to low-voltage regulated DC power for the internal components of a computer. You are building a new computer. You are deciding which type of power supply to install. Which of the following definitions BEST describes a valid type of power supply? Correct Answer: A single-rail power supply provides one rail (PCB trace). This provides the best safety for the computer by providing a single point of shutdown in the event of a short circuit. Correct Answer: A single-rail power supply provides one rail (PCB trace) used to always provide equal wattage to all devices attached to the power supply. Correct Answer: A dual-rail power supply provides separate rails (PCB traces) used to provide equal wattage to the devices attached to each rail. Correct Answer: A dual-rail power supply provides separate rails (PCB traces) used to balance the power load between multiple circuits, which prevents any one circuit from becoming overloaded.