bio lab photosynthesis - Morgan Murphy

3. Fast help needed to answer this Engineeing question. Check image.   Postive feedback for right answer :)

yluils (T.) 4 B Take Test: Quiz 1 CT2 - Circuits A bb.cas.edu.om/webapps/assessment/take/take.jsp?course_assessment_id=_9460_1&course_id=_18678_18&content_id=_194535_1&question_num_5.x=0&toggle_state=qSho. E Apps O YouTube Maps M Gmail A Translate Remaining Time: 24 minutes, 12 seconds. A Question Completion Status: 1 2 3 4 5 What is the result of the following in time domain? 20 sin 400t + 10 cos(400t + 60) – 5sin(400t – 20) 9.44 cos(400t-44.7) Non of the answers 22.79 cos(400t+27) 15.5 cos(400t-44.7) > A Click Submit to complete this assessment. « < Question 5 of 5 Save and Submit 1:06 AM P Type here to search A O G 40 ENG 3/30/2021

Write the answers precisely, do not elaborate unnecessarily, and don't use chatgpt, if i caught it I'm gonna downvote Question: Discuss the electrochemical techniques that are useful to study the capacitive properties of a material. Highlight the importance of each technique

The student engineer of a campus radio station wishes to verify the effectiveness of the lightning rod on the antenna mast (see the figure below). The unknown resistance Ry is between points C and E. Point E is a "true ground," but is inaccessible for direct measurement because the stratum in which it is located is several meters below Earth's surface. Two identical rods are driven into the ground at A and B, introducing an unknown resistance Ry. The procedure for finding the unknown resistance Ry is as follows. Measure resistance R, between points A and B. Then connect A and B with a heavy conducting wire and measure resistance R2 between points A and C.

The student engineer of a campus radio station wishes to verify the effectiveness of the lightning rod on the antenna mast (see the figure below). The unknown resistance Ry is between points C and E. Point E is a "true ground," but is inaccessible for direct measurement because the stratum in which it is located is several meters below Earth's surface. Two identical rods are driven into the ground at A and B, introducing an unknown resistance Ry. The procedure for finding the unknown resistance Rx is as follows. Measure resistance Ry between points A and B. Then connect A and B with a heavy conducting wire and measure resistance R, between points A and C.

8. Liquids with solid impurities a) Have higher dielectrie strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average dc voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35

Required information Problem 06.033 Section Break Consider the circuit given below. Ves +5 V Om storsi Ra mA Problem 06.033.a Vcc +5V 470 52 Smat apps%252Fporta252framesetsp Determine the collector current when Rg= 31 k0 and FE-100 Calculate using the second approximation. Round the final answer to two decimal places.

1/ Suppose that there are two types of H.V.T.Ls operating at the same voltage and carrying the same current, but one of them with smooth shapewhile the other with standard shape. Which of them, you will choose? a. choosing the smooth one. b. choosing the standard one. c. choosing the one with hollow construction shape. d. all these answers are wrong. 2/ As the ambient temperature in crease the disruptive critical voltage of coron a is: a. Decreased b. Increased c. No effect d. All these answers are wrong. 3/ Using HV underground cable improvevoltageprofile and power factor in any loaded inductive electrical grid because. a. Due to its inductive power effect. b. Due to resistive Effect. c. Due to its capacitive power effect. d. All of the above answers are wrong.

Observe the diagram, imagine that you are going into a 4-wall mirror dark room with a flashlight. As soon as you entered the room, you pointed the flashlight with an angle of 330. Continue the diagram below by creating a line and calculating the angle of incident light and angle of reflection on the 4-wall mirror room.

1. Answer the subparts A&B with the step, based on the Image. This question Q&A please no reject and solve thank u A) Based on the measurement data above, indicate that there is an error in the measurement      data. Give an explanation of the answers given. B) Determine in which element there is an error in the measurement data. What should be       the correct measurement result. Give an explanation of the answers given.

QUESTION 1 (a) Table Q1(a) is given. Calculate the precision of the 9th measurement. The actual value for 9th resistor is 2000 Q. Calculate the absolute error, percentage error and percentage els come t what accuracy for 9ª measurement. Table Q1(a) Resistor Measurement (N) 1 2002 2010 3 1987 +6d 72 4 2007 5 1999 for pary mot work 6. 1993 17209 7 1997 8. 2008 2010 10 2001 11 1995 12 1991 (b) A DC source is connected in series with a resistor. A ±1% full scale accuracy voltmeter with range of 150 V and ±1.5% full scale accuracy ammeter with range of 100 mA ammeter are used to measure voltage and current in a circuit. The voltmeter and ammeter reading is 80 V and 70 mA respectively. Calculate the limiting error of the power. Determine the power dissipated and the absolute error.