D26F3A94-09A6-494F-A3D7-D2594F8D5422

Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…

Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P

Suppose the current in this circuit is I = -35 A. The voltage drop across each circuit element is as given in the table below. From this information, determine, for each of these circuit elements, (i) whether an active or passive sign convention is being used for that element, (ii) whether that element is absorbing or producing a net (positive) amount of electrical power. In each answer box within the table below, type the correct choice from among the bold-faced words above. - A A B C A + с B + V₂ Circuit element Voltage drop Sign convention? Absorbing or producing net electrical power? -5 V -6 V 1 V -

From the picture of panel  name plate, explain each and every parameter displayed in it in a brief manner.

B3

Q1

The system having ±0.5% of F.S.D if the full scale deflection is 50 units, then accuracy is _____ a. ±0.25 b. ±1 c. ±0 d. ±0.5

Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C     what is the answer? VD?

Please answer with detail and how it is done. Photo is attached with the questions.

In the figure, the ideal batteries have emfs ℰ1 = 25.0 V and ℰ2 = 0.500ℰ1, and the resistances are each 2.14 Ω. (a) What is the current in resistor 2? ______________A(b) What is the current in resistor 3? ______________A (please show the units when working through the problem so that I can follow it easier)

According to the following specifications, a single solar 295-watt solar panel has maximum power operation voltage at 24 volts. What is the maximum number of solar panels that can be used in a single string? a. 35 solar panels. b. 30 solar panels. c. 25 solar panels. d. 40 solar panels. e. 20 solar panels.

A computer's power supply converts mains AC to low-voltage regulated DC power for the internal components of a computer. You are building a new computer. You are deciding which type of power supply to install. Which of the following definitions BEST describes a valid type of power supply? Correct Answer: A single-rail power supply provides one rail (PCB trace). This provides the best safety for the computer by providing a single point of shutdown in the event of a short circuit. Correct Answer: A single-rail power supply provides one rail (PCB trace) used to always provide equal wattage to all devices attached to the power supply. Correct Answer: A dual-rail power supply provides separate rails (PCB traces) used to provide equal wattage to the devices attached to each rail. Correct Answer: A dual-rail power supply provides separate rails (PCB traces) used to balance the power load between multiple circuits, which prevents any one circuit from becoming overloaded.

The waveform of a voltage source is shown in the given figure. Let A = 2 and B = -3.8. Determine the average current supplied to a 10-ohm resistor connected across the voltage source.  The average current supplied to a 10-ohm resistor connected across the voltage source is  ______A.