B3 4:00:00 AMbave, Dawvve, avve, Suppose you have two point charges each of 79 nC.Dave, Ananya Ananya dave@icloud.comtheexpertta.com-tracking id: STRS-28-92-4C-BCA7-35191. In accordance with Expert TA'S Terms of Service. copying this information fo any solutions sharDoing so may result in termination of your Expert TA AccountHow many millimeters apart must the two charges be to have a force of 0.85 N between them?d =sin)cos)tan()89.HOMEcotan()asin)acos)E 45.atan()acotan()sinh()23.cosh)tanh()cotanh()ENDDegreesRadiansVOACKSACECLIAR

The value of the first charge is, q1=79 nC The value of the first charge is, q2=79 nC Since the…

Dawvre, avve, Suppose you have two point charges each of 79 nC. Ananya Ananya daveicloud.com xpertta com - tracking id: STRS-2B-92-4C-BCA7-35191. In accordance with Expert TA's Terms of Service. copying this informatic so may resuli in termination of your Expert TA Account How many millimeters apart must the two charges be to have a force of 0.85 N between them? d = sin) cos) 7 8 E A 4 tan() 9. HOME cotan() asin) acos) 5 6 atan() acotan() sinh 123 cosh) tanh() cotanh() Degrees Radians

Dawvre, avve, Suppose you have two point charges each of 79 nC. Ananya Ananya daveicloud.com xpertta com - tracking id: STRS-2B-92-4C-BCA7-35191. In accordance with Expert TA's Terms of Service. copying this informatic so may resuli in termination of your Expert TA Account How many millimeters apart must the two charges be to have a force of 0.85 N between them? d = sin) cos) 7 8 E A 4 tan() 9. HOME cotan() asin) acos) 5 6 atan() acotan() sinh 123 cosh) tanh() cotanh() Degrees Radians

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If triangular copper bus bar is 0.75 millimeter on the base and 100 millimeters in the height, find the cross-section. What is the cross-sectional area in square centimeters? Carry the answer to two decimal places.
Please provide Handwritten answer
What unit of measurement is used for fhe diameter of fhe wires
QUESTION -8 The plot describing the thermal characteristics of copper wire is given in the figure. Using this plot, for a 1000ft length copper wire with 10 Ω resistance at room temperature (20oC)a) Calculate the resistance value at 100oC.b) Calculate the power consumed in the cable carrying 10A current at this temperature (100oC) in units Watt.c) Calculate the amount of energy consumed in the cable during a day with the conditions in (a) and (b) in units Joules.d) A motor with 600Watt output power that works with 85% efficiency is driven with 10A current carried in the cable at 100oC. Calculate the amount of power transformed (dissipated) into heat in this system.e) Consider that a cooling system is used to cool the cable to 50oC and the cable carries 10A current. How many watts should be the maximum amount of power consumed by the cooling system in order to gain power (consume less total power).
A. 0.5 A Given the circuit below, find the current /. B. 1A C. 0.75 A in D. 0.6 A 40V 1052 iA
Problem 3: A factory manufactures a specific copper part. It is found at a certain temperature the resistance in m2 of this part is normally distributed with mean of 23.8 and standard deviation of 1.23. Among 5000 units of such parts, how many units are likely to have a resistance (a) less than 23? (b) greater than 24? (c) between 24.2 and 24.5?
None
2. Explain the construction of squirrel cage I.M.
1. Solve the following resistance problems: a. A 4.2 cm long copper wire has a cross-sectional area of 3.7 mm?. Determine the resistance of that wire. Check the resistivity of Copper int the table given in the textbook. b. Consider a 1.6 cm long silver wire. What is the cross-sectional area of the wire for it to have a resistance of 2.2 x 102 0.
Find the current iy ANSWER:______________mA
21 Balance is obtained in a DC potentiometer at a length of 71 cm when using a standard cell of 53.2 volts. Calculate the EMF of a dry cell if balance is obtained with a length of 20 cm. a. 0.07 b. 14.99 c. 0.01 d. 188.86