POE Final

pdf

School

Full Sail University *

*We aren’t endorsed by this school

Course

REC2132

Subject

Electrical Engineering

Date

Feb 20, 2024

Type

pdf

Pages

5

Uploaded by DoctorGazellePerson1034

Report
Principles of Electronics – Lab Workbook 1 Lab 11: Practical Exam Leave the following pages completely blank until your Lab Specialist directs you to start your Lab Final Exam during the last POE Lab period. Name: ___________________________________________ Date: ______________________ Lab Specialist: _____________________________________________ Grade: _____________________ Remember to use correct units when appropriate! Magnetic Field Lines Diagram the field lines that exist around the following sources of magnetism. Directional arrows are not required for the coil . (3 points each): Bar Magnet Coil Current Carrying Conductor
Principles of Electronics – Lab Workbook 2 Ohm’s Law Complete the following Ohm’s Law drills using the (2) resistors provided. Show all work on math problems. Measure and document the values of the resistors: (3 points each) Resistor #1 actual value: _________________ Resistor #2 actual value: _________________ Series resistance 1. Calculate and document the series resistance of the two resistors. calculated value:_______________ (5 points) 2. Measure and document the series resistance of the two resistors. actual value: _________________ (5 points) Parallel resistance 3. Calculate and document the parallel resistance of the two resistors. calculated value:_______________ (5 points) 4. Measure and document the parallel resistance of the two resistors. actual value: _________________ (5 points)
Principles of Electronics – Lab Workbook 3 DC Current draw of a series load Apply your actual resistor values to the following diagram: 5. Calculate and document the current draw for a 9VDC power source. calculated value:_______________ (5 points) AC Current Draw of a Single Load Complete the following Ohm’s Law drill using the lamp, clamp meter, and clamp meter power cable provided: 6. Calculate and document the current draw of the provided light bulb with a 120V RMS power source. calculated value:_______________ (5 points) 7. Use a clamp meter and clamp meter power cable to measure and document the current draw of the provided light bulb with a 120V RMS power source. Request Lab Specialist verification of your measurement. actual value: _________________ (5 points) Lab Specialist Initials: ______________
Your preview ends here
Eager to read complete document? Join bartleby learn and gain access to the full version
  • Access to all documents
  • Unlimited textbook solutions
  • 24/7 expert homework help
Principles of Electronics – Lab Workbook 4 Power Cable 1. Terminate the power cable with the power connector:(10 points total): Build quality: ________ (5 Points) Correct Wiring: ________ (5 Points) Crossover Testing 1. Using a 2Vpp sine wave, test the crossover to determine which (2) outputs are bad. Your frequency selection depends on the output being tested. 2. Crossover points: a. Sub – 75 Hz b. Low / Mid – 200Hz c. Mid / High – 7kHz Crossover ID: __________________ Circle the bad outputs: Sub Low Mid High Bad Output 1: ____________ Bad Output 2: ____________ (5 Points) (5 Points) PCB Construction Measure and document the value of each resistor pair. R 1 or 2 : ________________ R 3 or 4 : ________________ (2 Points) (2 Points) Measure and document an LED Turn-on voltage. LED 1 or 2 : ________________ (2 Points) Measure and document the value of a capacitor. C 1 : ________________ (2 Points) Build the Blinky LED circuit. Functions correctly: ______________ Solder quality: _______________ (6 Points) (6 Points)
Principles of Electronics – Lab Workbook 5 Graded XLR construction 1. Desolder and cut the Male XLR cable ends. 2. Rebuild the XLR cable after a Lab Specialist verifies it has been desoldered. 3. Present the XLR cable to an instructor for grading. Male XLR: Score _____(5 points) __________ Insufficient solder (-1 point each, -5 max) __________ Excessive solder __________ Nicked wire __________ Melted insulation __________ Excessive exposed wire __________ Cold solder joint __________ Excessive ground wire cut off __________ Frayed wire/wires __________ Shells on wrong side __________ Missing hardware __________ GND not soldered to pin 1 Correct wiring Score _____(5 points)