Copy of 5CL Pre-Lab 4 Submission Template - S24v2

(01) Zener Diode Circuits. (Course: Electronic Devices and Circuit Theory) -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.

Q1.) a) PMMC meter has (10mA) half scale current deflection and (1500) internal resistance. Use this meter to design a dc multimeter of indirect ammeter and direct voltmeter methods to measure the following ranges of current and voltage: 50mA, 100mA, 1A, 5V, 50V, and 150V. Draw the circuit diagram of this multimeter with a control switch that can be used to measure either current or voltage.

This multiple choice Questions from MEASUREMENTS INSTRUMENTATION course.

Draw the schematic symbol with 4 each type

Needs Complete typed solution with 100 % accuracy.

Summarize on how testing is carried out on isolators and circuit breakers of high voltage system. High voltage engineering

A resistor has a resistance of 20 ohms at 30 degrees Celsius and 32 ohms at 90 degrees Celsius. Find its resistance at 125 degrees Celsius. Determine also the temperature coefficient at 100 degrees Celsius. (Please Show Complete solution and write properly) (Round off the final answer to the 4th decimal if possible and box the final answer)

Fill in the blanks for Ampacity, Voltage, Power and Resistance.

Question 3: A very simple model for the distribution of clectricity to a typical home is shown in the figure below. Some of components labeled a, b, c, d, c, f, g and h represent the electrical source to the home, some represent the wires that carry the electrical current from the source to the devices in the home requiring electrical power, some represent lamps, televisions, hair dryers and other devices that require power. Assume you are an engineer in charge of a project and one of your subordinate engineers reports that the interconnection in the figure does not pass the power check. The data for the interconnection are given in the table below. Is the subordinate correer? Explain your answer. If the subordinate is correct, find the error in the data. Explain your answer clearly. Based on your answer identify that which label(s) used for the electrical source, wires or other devices. a e h

Determine the nodes/junctions, Current (I), Loops, Voltage drop on each Resistor (R), and Power (P) on each Resistor (R) with the following given and illustration: Use the following given for batteries and resistors (color bands for your value of resistors, use the lower limit).  R1 = red red black goldR2 = orange green black silverR3 = white orange black goldR4 = green violet brown goldR5 = violet red black silverR6 = yellow green black silverR7 = brown black black gold V1 (lower left) = 100VV2 (top center) = 150VV3 (lower right) = 200V

1.2 PLEASE ANSWER THE RESISTANCE RATING AND THE QUESTION BELOW.

please solve asap and thanks

Make an essay about Kirchoff's Law (Voltage and Current Law). Include its definition, uses, application, importance, and limitations. Include also recommendations when using Kirchoff's Law. Please make it TYPEWRITTEN and NOT HANDWRITTEN so I can copy paste it.

expected output to be seen in the oscilloscope

Short circuit is occurred when: Select one: a. The voltage between the two terminals is zero although there may be a nonzero current between the terminals. b. All of the given answers. c. There will be a zero-resistance connection between terminal A and B and therefore the 2 terminals are at the same voltage. d. A pair of terminals connected by a wire (of zero resistance).

Already got part 1 only answer part 2

1. Answer the subparts A&B with the step, based on the Image. This question Q&A please no reject and solve thank u A) Based on the measurement data above, indicate that there is an error in the measurement      data. Give an explanation of the answers given. B) Determine in which element there is an error in the measurement data. What should be       the correct measurement result. Give an explanation of the answers given.

What is K Map and how to make table through k map and how to grouping. i) Implement half subtractor take out equation and make circuit diagram.  NOTE: Write in Hand Written Form on page

1. Explain the principle of operation of Figure 1. Derive the equations that govern each block of the circuit.  2.Define the features and technical specifications based on Figure 1 requirement.  3.Design the high voltage side circuits and state equation(s) (that was derived in question 1) to justify the values used in your calculation. Specify practical values or actual component part number with reference from real worldwide components.  4. Design the low voltage side circuits and include equations to justify the values used in your calculation. Specify practical values or actual component part numbers with reference from real worldwide components. Include any heatsink calculation when required to ensure semiconductors do not overheat and keep the junction temperature below 125 degree Celsius.  5. Simulate, using CAD software, the low voltage side circuit to see its regulation. (Submit the simulation file together with the report.) a. Plot the output voltage (with its ripple voltage…

Typing format..

3. The figure on the left below shows a schematic diagram of a battery. The voltage measured by U1 is called the terminal voltage given R1 = 1 ohm. In the figure on the right below, the terminal voltage of each of the battery-resistor combination is Vr = 1.5 volts. Find the following: a. The current passing through R5. b. The currents passing through R1 and R3 C. The voltage across R1. d. The voltage of the battery EMF. e. The percentage of voltage loss ot the battery due to the internal resistance R1. The power dissipated by the internal resistance R1. g. The power dissipated by R5 if R1 = R2 = R3 = R4 = 0. h. The percentage of power dissipation loss due to the four resistors R1, R2, R3, and R4 f. R1 R3 S10 R1 U1 1.500 EMF EMF R5 100 V1 R2 $10 EMF R4 EMF EMF

None

1. Which of the figures is equivalent to the reference circuit?

1.1 Please solve and explain.

Please help me with this worksheet. Please fill in the table, answer the questions and make both circuits A and B on Tink

2. Does ?a three digit color coding of resistor values? limit producible resistor value ranges? Why? If you need to increase these range what would be your solution??

2. Please respond to question in attached image.  Thank you.

2. A. What parameters can be measured with a digital multimeter (DMM)? B. How does the DMM measure each parameter given that its internal circuitry actually only responds to voltage? C. What is the input resistance of the DMM on voltage ranges and why is this important? D. What voltage will the DMM read in the circuit below? Show computations. www DMM