The IUPAC name for the molecule is to be given. Concept introduction: In the IUPAC nomenclature , the longest continuous carbon chain is considered as the parent chain. The name of this corresponding parent chain will be the root of the molecule’s name. Identify the substituents and add the name of the substituent as a prefix to the left of the root. In case of two or more different substituents, the alphabetical order is considered. Number each carbon atom of the chain sequentially, beginning with C1 at one end of the chain, so that the carbon atom to which the substituent is bonded receives the lowest possible number. The number assigned to the carbon that is bonded to the substituent is called the locator number or locant. The locator number is written to the left of the substituent name and a hyphen is added to separate the locator number from the rest of the name.

Question

Want to see the full answer?

Answer 1

Question

Chapter A, Problem A.5P

Interpretation Introduction

Interpretation:

The IUPAC name for the molecule is to be given.

Concept introduction:

In the IUPAC nomenclature, the longest continuous carbon chain is considered as the parent chain. The name of this corresponding parent chain will be the root of the molecule’s name. Identify the substituents and add the name of the substituent as a prefix to the left of the root. In case of two or more different substituents, the alphabetical order is considered. Number each carbon atom of the chain sequentially, beginning with C1 at one end of the chain, so that the carbon atom to which the substituent is bonded receives the lowest possible number. The number assigned to the carbon that is bonded to the substituent is called the locator number or locant. The locator number is written to the left of the substituent name and a hyphen is added to separate the locator number from the rest of the name.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

A cylinder contains 12 L of water vapour at 150˚C and 5 atm. The temperature of the water vapour is raised to 175˚C, and the volume of the cylinder is reduced to 8.5 L. What is the final pressure of the gas in atmospheres? assume that the gas is ideal

On the next page is an LC separation of the parabens found in baby wash. Parabens are suspected in a link to breast cancer therefore an accurate way to quantitate them is desired. a. In the chromatogram, estimate k' for ethyl paraben. Clearly indicate what values you used for all the terms in your calculation. b. Is this a "good" value for a capacity factor? Explain. c. What is the resolution between n-Propyl paraben and n-Butyl paraben? Again, indicate clearly what values you used in your calculation. MAU | Methyl paraben 40 20 0 -2 Ethyl paraben n-Propyl paraben n-Butyl paraben App ID 22925 6 8 min

d. In Figure 4, each stationary phase shows some negative correlation between plate count and retention factor. In other words, as k' increases, N decreases. Explain this relationship between k' and N. Plate Count (N) 4000 3500 2500 2000 1500 1000 Figure 4. Column efficiency (N) vs retention factor (k') for 22 nonionizable solutes on FMS (red), PGC (black), and COZ (green). 3000 Eluent compositions (acetonitrile/water, A/W) were adjusted to obtain k' less than 15, which was achieved for most solutes as follows: FMS (30/70 A/W), PGC (60/40), COZ (80/20). Slightly different compositions were used for the most highly retained solutes. All columns were 50 mm × 4.6 mm id and packed with 5 um particles, except for COZ, which was packed with 3 um particles. All other chromatographic conditions were constant: column length 5 cm, column j.§. 4.6 mm, flow rate 2 mL/min, column temperature 40 °C, and injection volume 0.5 μL Log(k'x/K'ethylbenzene) FMS 1.5 1.0 0.5 0.0 ཐྭ ཋ ཤྩ བྷྲ ; 500 0 5 10…