Explanation Show the quarter circular area is divided into three segments as in Figure 1. Express the surface area of the ring using the theorem of Pappus and Guldinus. A = θ × ∑ r ¯ L (I) Here, the surface area of revolution is A , the angle of revolution measured in radians is θ , the perpendicular distance from the axis of revolution to the centroid of the generating curve is r ¯ , and the length of the generating curve is L . Since the angle of revolution is measured in radians, θ = 2 π rad Substitute 2 π rad for θ in Equation (I). A = 2 π × ∑ r ¯ L (II) Conclusion: Refer to Figure 1 and use spreadsheet to calculate the values of L , r ¯ , and r ¯ L for three segments as shown in Table 1. Segment L ( ft ) r ¯ ( ft ) r ¯ L ( ft 2 ) 1 a 2 a 2 a 2 2 π a

14th Edition

ISBN: 9780135681879

Author: HIBBELER

Publisher: PEARSON

See similar textbooks

Concept explainers

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related t…

Videos

Question

Chapter 9.3, Problem 96P

To determine

The surface area of the ring (A) .

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.3, Problem 95P

Chapter 9.3, Problem 97P

Students have asked these similar questions

I need handwritten solution with sketches for each

Given answers to be: i) 14.65 kN; 6.16 kN; 8.46 kN ii) 8.63 kN; 9.88 kN iii) Bearing 6315 for B1 & B2, or Bearing 6215 for B1

(b) A steel 'hot rolled structural hollow section' column of length 5.75 m, has the cross-section shown in Figure Q.5(b) and supports a load of 750 kN. During service, it is subjected to axial compression loading where one end of the column is effectively restrained in position and direction (fixed) and the other is effectively held in position but not in direction (pinned). i) Given that the steel has a design strength of 275 MN/m², determine the load factor for the structural member based upon the BS5950 design approach using Datasheet Q.5(b). [11] ii) Determine the axial load that can be supported by the column using the Rankine-Gordon formula, given that the yield strength of the material is 280 MN/m² and the constant *a* is 1/30000. [6] 300 600 2-300 mm wide x 5 mm thick plates. Figure Q.5(b) L=5.75m Pinned Fixed

Chapter 9 Solutions

ENGINEERING MECHANICS: STATICS

Ch. 9.1 - In each case, use the element shown and specify...Ch. 9.1 - Determine the centroid (x,y) of the shaded area....Ch. 9.1 - Determine the centroid (x,y) of the shaded area....Ch. 9.1 - Determine the centroid of the shaded area. Prob....Ch. 9.1 - Locate the center of mass x of the straight rod if...Ch. 9.1 - Locate the centroid of the homogeneous solid...Ch. 9.1 - Locate the centroid z of the homogeneous solid...Ch. 9.1 - Locate the center of mass of the homogeneous rod...Ch. 9.1 - Determine the location (x,y) of the centroid of...Ch. 9.1 - If the rod has a weight per unit length of 100...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The surface area of the ring ( A ) .

Solution Summary: The author explains the surface area of the ring using the theorem of Pappus and Guldinus.

Concept explainers

Videos

The surface area of the ring (A) .

Want to see the full answer?

Chapter 9 Solutions