The reason for the occurrence of NaCl as a solid is to be determined. Concept introduction: Lattice energy is the amount of energy released when the ions combine to form an ionic compound. It is determined to measure the strength of the ionic interactions present in the lattice. A high negative value of lattice energy is the reason behind the formation of ionic compounds. The lattice energy of compounds depends upon generally three factors as follows: 1. Ionic Size 2. Ionic Charge 3. Arrangement of ions in the lattice Lattice energy depends upon the ionic interaction between the ions present in the lattice. Therefore, lattice energy decreases with the increase in ionic size and decrease in the ionic charge.

Question

Want to see the full answer?

Answer 1

Question

Chapter 9, Problem 9.18P

Interpretation Introduction

Interpretation:

The reason for the occurrence of NaCl as a solid is to be determined.

Concept introduction:

Lattice energy is the amount of energy released when the ions combine to form an ionic compound. It is determined to measure the strength of the ionic interactions present in the lattice. A high negative value of lattice energy is the reason behind the formation of ionic compounds.

The lattice energy of compounds depends upon generally three factors as follows:

1. Ionic Size

2. Ionic Charge

3. Arrangement of ions in the lattice

Lattice energy depends upon the ionic interaction between the ions present in the lattice. Therefore, lattice energy decreases with the increase in ionic size and decrease in the ionic charge.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

Recent advancements in liquid chromatography include the development of ultrahigh pressure liquid chromatography (UHPLC) and an increased use of capillary columns that had previously only been used with gas chromatography. Both of these advances have made the development of portable LC systems possible. For example, Axcend Corp. makes a portable system that uses a capillary column with an internal diameter of 150-μm-that is packed with 1.7-um stationary phase particles. In contrast, a traditional LC column has a 4.6 mm internal diameter and utilizes 5-um stationary phase particles. a) Explain one advantage that is afforded by the use of a capillary column in liquid chromatographic separation. Explain one disadvantage of capillary columns. b) Explain how the use of smaller stationary phase particles can improve the resolution of a separation. Include any relevant equations that support your explanation. c) A scientist at Rowan University is using the Axcend LC to conduct analyses of F…

This paper describes the use of fullerene molecules, also known as buckyballs, as a stationary phase for liquid chromatography. The performance of the fullerene-modified stationary phase (FMS) is compared to that of a more common C18 stationary phase and to two other carbon-based stationary phases, PGC and COZ. A. 10A OM B. - Figure 1. Idealized drawing of the cross-section of a pore inside a silica particle, showing the relative densities of aminopropylsilyl (red/green) and fullerene (blue) groups: (A) full cross- section; (B) detailed view of covalent bonding of fullerene to the silica surface. Surface densities of silyl and fullerene groups were inferred from elemental composition results obtained at each stage of the synthesis (see Table 1). Absorbance (mAU, 220 nm) 700 600 500 400 300 200 100 a. Define selectivity, a, with words and an equation. b. Explain how the choice of stationary phase affects selectivity. c. Calculate the resolution of the nitrobenzene and toluene peaks in…

Normalized Intensity (a. u.) 0.5 1.0 A 3D-printed GC column (shown below) was created for use with "micro" gas chromatography applications. To prove its utility, it was used to separate a mixture of alkanes (C9-C18, C22, C24). For the separation shown below, the column temperature was ramped from 40 °C to 250 °C at a rate of 30 °C per minute. (a) 9 10 = 1 mm 12 13 15 22 0.0 0 100 200 300 400 Time (sec) a) What detector would you use for this analysis? Justify your selection. b) Explain how the chromatogram would change if the separation was run isothermally. c) Explain how the chromatogram would change if the temperature ramp were increased to 50 °C per minute.