Fundamentals of Geotechnical Engineering (MindTap Course List)
5th Edition
ISBN: 9781305635180
Author: Braja M. Das, Nagaratnam Sivakugan
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 9, Problem 9.14P
(a)
To determine
Calculate the over-consolidation ratio of the clay.
(b)
To determine
Calculate the consolidation settlement.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
In a normally consolidated clay specimen, the following
data are given from the laboratory consolidation test.
e₁ = 1.10
σ= 65.0 kN/m²
€₂ = 0.85
o₂ = 240.0 kN/m²
a. Find the compression index C.
b. What will be the void ratio when the next pressure incre-
ment raises the pressure to 460.0 kN/m²?
Question attached
Refer to the soil profile shown in Figure P2.12. The clay is normally consolidated. A laboratory consolidation test on the clay gave the results: If the average effective stress on the clay layer increase by 50 kN/m2.a. What would be the total consolidation settlement?b. If Cv = 9.36 x 10-4 cm2/sec, how long will it take for half the consolidation settlement to take place?
Chapter 9 Solutions
Fundamentals of Geotechnical Engineering (MindTap Course List)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A given saturated clay is known to have effective strength parameters of c' = 10 kPa and = 28°. A sample of this clay was brought to failure quickly so that no dissipation of the pore water pressures %3D could occur. At failure it was known that o KPa, o = 10 KPa and = 20 kPa. %3D (a) Estimate the values of o, and oz at failure (b) Use the Mohr circle to illustrate the effective stress and total failure stress.arrow_forwardx in red is equal to 39arrow_forwardFor a normally consolidated soil, the following is given: Determine the following: a. The compression index, Cc. b. The void ratio corresponding to pressure of 200 kN/m2arrow_forward
- A 75 mm diameter clay specimen was consolidated in an oedometer under 200 kPa. At the end of consolidation, the void ratio is 0.863 and the specimen thickness is 18.51 mm. When the stress increment of 200 was added to the current vertical stress of 200 kPa, the specimen consolidated to a thickness of 17.56 mm. Assuming that the clay was normally consolidated under the vertical stress of 200 kPa, find the a) coefficient of volume compressibility in (MPa)^-1 and rounded to the 3rd decimal place.b) and the compression index of the clay rounded to the 2nd decimal place.arrow_forwardThe laboratory consolidation data for an undisturbed clay specimen are as follows: e1 = 1.12 P₁ = 90 kPa e2 = 0.90 P2 = 450 kPa 1. Compute the value of the compression index. 2. Compute the value of the swell index assuming it is equal to 1/6 the value of the compression index. 3. Compute the void ratio for a pressure of 600 kPa. 4. Compute the coefficient of compressibility. 5. Compute the value of the coefficient of volume compressibility.arrow_forwardGeotechnicalarrow_forward
- A saturated clay sample in an oedometer is under vertical pressure of 120 kPa and is at a normally consolidated state. The void ratio and the sample height at this stage are 1.21 and 18.40 mm respectively. When the vertical stress was increased to 240 kPa at the end of the consolidation, the thickness of the sample was reduced to 16.80 mm. When the vertical pressure was reduced to the original value of 120 kPa, the sample heaved to a thickness of 16.95 mm. Estimate both the compression index and recompression index of the clay. What would be the reduction in thickness from now if the vertical pressure was increased by 200 kPa? What is the average coefficient volume compressibility during this pressure increment?arrow_forwardExperimental data for clay specimen obtained initial values of e1 = 1.12 and P1 = 90 kPa, and final values of e2 = 0.90 and P2 = 460 kPa Solve for the compression indexarrow_forwardPlease answer 12.17arrow_forward
- A clay sample underwent a consolidation test in the lab. The clay specimen has drainage on both sides and a height of 25.4 mm. Assume that the clay sample's preconsolidation pressure was less than 150 kPa prior to the consolidation test. The void ratio was 0.96 when the applied effective vertical pressure was 150 kPa. When the vertical effective pressure increased from 150 to 220 kPa, the void ratio at the end of consolidation and compression was 0.88. It was discovered that the sample needed 3 minutes to consolidate by 30%. Following the consolidation test, a swelling/unloading test was conducted, in which the vertical effective stress was lowered from 220 to 150 kPa and the end-of-swelling void ratio was determined to be 0.9. Required a. The compression index of the clay b. The swelling index of the clay C. The height of the clay sample at the end of compression d. The coefficient of consolidation of the clay e. The final height of the clay sample at the end of swellingarrow_forward1. The pressure versus void ratio data determined from a consolidation test on an undisturbed clay specimen are as follows: Applied Pressure (kPa) 20 40 80 160 320 640 1280 320 80 20 0 Void Ratio 0.953 0.948 0.938 0.920 0.878 0.789 0.691 0.719 0.754 0.791 0.890 (a) Plot this pressure versus void ratio data on a semi-logarithmic graph. (b) Determine the equations for the virgin compression curve and for the rebound curve for unloading starting at 1,280 kPa. (c) What are the corresponding compression and recompression indices for this soil? (d) Estimate the stress to which this clay has been preconsolidated. (After A. Casagrande.)arrow_forwardA sample of normally consolidated clay was subjected to a consolidated undrained triaxial compression test that was carried out until the specimen failed at a deviator stress of 50 kN/m2. The pore water pressure at failure was recorded to be 20 kN/m2 and confining pressure of 50 kN/m2 was used in the test. Determine the consolidated undrained friction angle.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Fundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage LearningPrinciples of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage LearningPrinciples of Geotechnical Engineering (MindTap C...Civil EngineeringISBN:9781305970939Author:Braja M. Das, Khaled SobhanPublisher:Cengage Learning
- Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781305081550Author:Braja M. DasPublisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...
Civil Engineering
ISBN:9781305970939
Author:Braja M. Das, Khaled Sobhan
Publisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781305081550
Author:Braja M. Das
Publisher:Cengage Learning