Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
3rd Edition
ISBN: 9780133593211
Author: Elizabeth A. Stephan, David R. Bowman, William J. Park, Benjamin L. Sill, Matthew W. Ohland
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 9, Problem 5ICA
A fluid with a specific gravity of 0.91 and a viscosity of 0.38 pascal seconds [Pa s] is pumped through a 25-millimeter [mm] diameter smooth pipe at an average velocity of 2.6 meters per second [m/s]. Determine the Reynolds number in the pipe for the system and indicate if the flow is laminar, transitional, or turbulent.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A sludge mixture having a specific gravity of 2.93 and a viscosity of 0.09 grams per centimeter second [g/(cm•s)] is pumped from a reactor to a holding tank. The pipe is a 2.5 inch [in] diameter pipe. The velocity is 1.8 meters per second [m/s]. Determine the Reynolds number in the pipe for the system and indicate if the flow is laminar, in transition, or turbulent.
Send 20 degree Celsius of water at 4.0 [m3 / h]. How many [in] of standard steel pipe should be used to make the average flow rate in the pipe 1.5 ~ 2 [m / s]? At this time, determine the average flow rate and the flow of the fluid.
The volume flow rate of water is 662,73 liters/min. Calculate the maximum length of the pipe [m], which can be
used without cavitation? (NOTE: Take water temperature as 10 °C)
Chapter 9 Solutions
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Ch. 9.2 - The heat loss (Q/t, in units of joules per second...Ch. 9.2 - Prob. 2CCCh. 9.2 - What are the dimensions of the value 6 in the...Ch. 9.4 - The Euler number is a function of the pressure...Ch. 9 - Prob. 1ICACh. 9 - Prob. 2ICACh. 9 - Prob. 3ICACh. 9 - Prob. 4ICACh. 9 - A fluid with a specific gravity of 0.91 and a...Ch. 9 - Brine, with a density of 1.25 grams per cubic...
Ch. 9 - When a simple turbine is used for mixing, the...Ch. 9 - Prob. 8ICACh. 9 - Prob. 9ICACh. 9 - 1. While researching fluid dynamics, you come...Ch. 9 - 2. While researching fluid dynamics, you came...Ch. 9 - 3. While researching fluid dynamics, you come...Ch. 9 - 4. The Arrhenius number (Ar) is the dimensionless...Ch. 9 - 5. The Biot number (Bi) is the dimensionless...Ch. 9 - 6. A biodegradable fuel having a specific gravity...Ch. 9 - 7. A sludge mixture having a specific gravity of...Ch. 9 - 8. Water (specific gravity = 1.02; viscosity =...Ch. 9 - Prob. 9RQCh. 9 - 10. The Peclet number is used in heat transfer in...Ch. 9 - 11. When a fluid flows slowly across a flat plate...Ch. 9 - 12. In modeling the flow of liquid in a piping...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
5.1 through 5.9
Locate the centroid of the plane area shown.
Fig. P5.1
Vector Mechanics for Engineers: Statics and Dynamics
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics, 11th Edition
A 20-lb force is applied to the control rod AB as shown. Knowing that the length of the rod is 9 in. and that t...
Statics and Mechanics of Materials
Locate the centroid of the area. Prob. 9-17
Engineering Mechanics: Statics
What types of coolant are used in vehicles?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
A nozzle at A discharges water with an initial velocity of 36 ft/s at an angle with the horizontal. Determine ...
Vector Mechanics for Engineers: Dynamics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The vertical U-Section of a water distribution system seen on the drawing is considered. All hydraulic and dimensional data of the flow piece are known as given below. Calculate the Horizontal and Vertical components of the force acting on the flanges connecting the piece to the system. Q₁ = 30 [lt/s], P₁ = 200 [kPa], d₂ = 50 [mm] Q2 = 22 [lt/s], Q = 8 [lt/s], P2 = 150 [kPa], P = 100 [kPa], d₂ = 100 [mm] 22 = 0,7 10³ [m²] P₂ 2₁ d2 19₂ ΤΩΡΩarrow_forwardThis is not a graded question. Solve asaparrow_forwardA gas flows of from a station (a) with pressure of 20[bar] through a pipe with 0.4[m] diameter and4000 [m] length to a different station (b). The pressure at the exit (station (b)) is 2[bar]. The gasand the sounding temperature can be assumed to be 300 K. Assume that the flow is isothermal,k=1.4, and the average friction f=0.01. Calculate the Mach number at the entrance to pipe and theflow rate.arrow_forward
- When crude oil with a specific gravity of 0.80 and a viscosity of 27 [p] is transported at 200 [m^3/h] using a 10" standard steel pipe, find the two losses (head loss) and pressure drop per 1 [km] of pipe length.arrow_forwardVelocity, v [m/s] (0,vo) Number Time, t [s] m (t₁, V₁) Given the above figure, where o = 2 m/s, v₁= 3 m/s, and ₁=1 s, what is the displacement over this time interval? Write your answer in metres to three significant figures. 00 BY SA USask Engineeringarrow_forwardA given model of smartwatch worn by a diver is rated for 5 atm. If the diver swam downwards in a brackish lake with water density of 63 lbm/ft3, how deep [ft] will he reach before water starts entering the watch above the rated pressure specification? Assume that atmospheric pressure is equal to 14.5 psi.arrow_forward
- Sinav The volume flow rate of water is 650,53 liters/min. Calculate the maximum length of the pipe [m], which can be used without cavitation? (NOTE: Take water temperature as 10 °C) amış den Length D-0.07 m C-0.08 mm Uygula Elevation 650m Elevation 653 m Kalan S Yanıt: Kontrol et ayfa Sonraki sayfaarrow_forwardDetailed explanation required (This is not a graded question)arrow_forwardPlease sol with steparrow_forward
- Air is allowed to flow from a reservoir with temperature of 21∘C and with pressure of 5[MPa]through a tube. It was measured that air mass flow rate is 1[kg/sec]. At some point on the tubestatic pressure was measured to be 3[MPa]. Assume that process is isentropic and neglect thevelocity at the reservoir, calculate the Mach number, velocity, and the cross-sectional area at thatpoint where the static pressure was measured. Assume that the ratio of specific heat isk=Cp/Cv=1.4.arrow_forwardIndustries involved in viscosity measurement [27, 29] continue to use the CGS system ofunits, since centimeters and grams yield convenient numbers for many fl uids. The absoluteviscosity ( μ ) unit is the poise, named after J. L. M. Poiseuille, a French physician who in1840 performed pioneering experiments on water fl ow in pipes; 1 poise =1 g/(cm-s). Thekinematic viscosity ( ν ) unit is the stokes, named after G. G. Stokes, a British physicist whoin 1845 helped develop the basic partial differential equations of fl uid momentum; 1 stokes =1 cm 2 /s. Water at 20 ° C has μ ~~ 0.01 poise and also ν ~~ 0.01 stokes. Express these resultsin ( a ) SI and ( b ) BG units.arrow_forwardA Venturi Tube develops low pressure on its throat, which can suck water from a deposit located under it. Assuming permanent flux with no losses, calculate the V1 necessaryto suck water from the deposit to the throat. D1 = 15 [mm]; D2 = 37 [mm]; h = 163 [mm]; pa = 101325 [Pa] (atmospheric pressure). Express the solution in [m/s]arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Chemical and Phase Equilibrium; Author: LearnChemE;https://www.youtube.com/watch?v=SWhZkU7e8yw;License: Standard Youtube License