Engineering Fundamentals: An Introduction to Engineering
Engineering Fundamentals: An Introduction to Engineering
6th Edition
ISBN: 9780357391273
Author: Saeed Moaveni
Publisher: Cengage Learning US
bartleby

Concept explainers

Question
Book Icon
Chapter 9, Problem 39P
To determine

Find the average velocity of the water leaving the tank.

Expert Solution & Answer
Check Mark

Answer to Problem 39P

The average velocity of the leaving water in ins, fts, and ms are 33.48ins_, 2.79fts and 0.85ms respectively.

Explanation of Solution

Given data:

Refer to the given Figure Problem 9.38 in the textbook, which shows the tank is filled by water using pipes 1 and 2.

The water level increases in the rate of 0.1 in/s.

The diameter of the tank is (dtank) 6 in.

Formula used:

Write the expression for the volume flow rate.

Q=VaverageAc

Here,

Ac is cross-sectional area, and

Vaverage is average velocity.

Calculation:

Consider that the constant water density.

From the given figure, write the volume flow rate expression for inlet and outlet volumetric flow rate expressions.

Q1+Q2Q3=Atankchangeintheheightofwatertime

Re-arrange the equation,

Q1+Q2Atankchangeintheheightofwatertime=Q3V1A1+V2A2Atankchangeintheheightofwatertime=V3A3[V1(π4)(d1)2+V2(π4)(d2)2(π4)(dtank)2(0.1ins)=V3(π4)(d3)2=Q3]        [A=π4d2,and[changeintheheightofwater]time=0.1ins]

Substitute 2fts for V1, 1.5fts for V2, 1 in. for d1, 1.75 in. for d2, 1.5 in. for d3, and 6 in. for dtank,

(2fts)(π4)(1in.)2+(1.5fts)(π4)(1.75in.)2(π4)(6in.)2(0.1in.s)=(V3)(π4)(1.5in.)2=Q3{[(2fts)(π4)(1ft12)2+(1.5fts)(π4)(1.75 ft12)2(π4)(6ft12)2(0.112fts)=(V3)(π4)(1.5ft12)2=Q3]}                      [1in.=112ft]0.0109ft3s+0.02505ft3s0.001636ft3s=0.01227ft2(V3)=Q30.0343ft3s=0.01227ft2(V3)=Q3

The values of Q3 and V3 are,

Q3=0.0343ft3s,

And

V3=0.0343ft3s0.01227ft2

V3=2.79fts (1)

Convert the unit of value in equation (1) from fts to ins.

V3=2.79×12ins[1ft=12in.]=33.48ins

Convert the unit of value in equation (1) from fts to ms.

V3=2.79×0.3048ms[1ft=0.3048ms]=0.85ms

Conclusion:

Hence, the average velocity of the leaving water in ins, fts, and ms are 33.48ins_, 2.79fts and 0.85ms respectively.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Note: (please show handwritten answers, and no AI usage !) Provide a clear, step-by-step handwritten solution (without any detailed explanations). Ensure the work is simplified and completed manually, adhering to expert-level accuracy. Refer to the provided image for clarity and ensure all calculations are double-checked for correctness before submission. Thank you!.   Question 1:  A cylindrical soil sample is connected to two water reservoirs: a) Determine the pressure, elevation, and total head at a point one meter above the bottom of the sample (point A). b) Calculate the pore pressure and effective stress at point A if the soil has a saturated unit weight of 18.7kN/m^3. c) Determine the water flow rate though the sample if the soil has a coefficient of permeability of 0.19 cm/s and the radius of the sample is 20 mm. d) Is it possible for the soil to reach the “quick condition”(zero effective stress) by raising the level of the water in the upper reservoir? Why or why not?. Question…
Note: Please provide a clear, step-by-step simplified handwritten working out (no explanations!), ensuring it is done without any AI involvement. I require an expert-level answer, and I will assess and rate based on the quality and accuracy of your work and refer to the provided image for more clarity. Make sure to double-check everything for correctness before submitting thanks!. Questions 1: A clay rich soil is totally saturated, has a bulk density of 2.12 g/cm3, and a void ratio of 0.33. a) Draw the full three phase diagram for this soil including all the volume and mass quantities. b) Determine the density of the soil solids. c) Determine the total density of the soil if the saturation was reduced to 50%.   Question 2: A soil sample was tested yielding the following grain-size distribution chart: (refer to the image provided) The soil fines (inorganic) were also tested and had a liquid limit of 76 and a plastic limit of 49 Determine the coefficients of uniformity and curvature.…
Note: Provide a clear, step-by-step handwritten solution (without any detailed explanations). Ensure the work is simplified and completed manually, adhering to expert-level accuracy. Refer to the provided image for clarity and ensure all calculations are double-checked for correctness before submission. Thank you!.   Question 1:  A cylindrical soil sample is connected to two water reservoirs: a) Determine the pressure, elevation, and total head at a point one meter above the bottom of the sample (point A). b) Calculate the pore pressure and effective stress at point A if the soil has a saturated unit weight of 18.7kN/m^3. c) Determine the water flow rate though the sample if the soil has a coefficient of permeability of 0.19 cm/s and the radius of the sample is 20 mm. d) Is it possible for the soil to reach the “quick condition”(zero effective stress) by raising the level of the water in the upper reservoir? Why or why not?. Question 2: A new structure is planned to be constructed in…
Knowledge Booster
Background pattern image
Civil Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning
Text book image
Sustainable Energy
Civil Engineering
ISBN:9781337551663
Author:DUNLAP, Richard A.
Publisher:Cengage,