Concept explainers
The change in the work potential of the air stored in the tank.
The change in exergy of the air stored in the tank.
Answer to Problem 120RP
The change in the work potential of the air stored in the tank is
The change in exergy of the air stored in the tank is
Explanation of Solution
Write the formula to calculate initial mass of air in the tank
Here, initial pressure of air is
Write the formula to calculate final mass of air in the tank
Here, final pressure of air is
Write the formula to calculate temperature of air at state 2 using isentropic relation
Here, temperature of air at state 1 is
Apply the conservation of mass to the tank which gives the following relation.
Here, rate of change in mass of air is
Write the equation for the rate of heat transfer using the first law of thermodynamics
Here, enthalpy of air is h, internal energy of air is u, volume of tank is V, specific heat capacities at constant pressure and constant volume are
From the final temperature equation and multiplying the above relation by
Integrate the above relation.
Apply the first law to the tank and compressor.
Here, rate of work potential of the air stored in the tank is
Integrate the above relation.
Here, change in the work potential of the air stored in the tank is
Apply the first law and second law to the tank and compressor and the mass balance incorporated. It gives,
Here, dead state temperature is
Integrate the above relation.
Here, reversible work done on the system is
Conclusion:
Refer Table A-2, "Ideal-gas specific heats of various common gases", obtain the properties of air at the room temperature.
Substitute
Substitute
Substitute
Substitute
The negative sign shows that the work is done on the compressor.
Thus, the change in the work potential of the air stored in the tank is
Substitute
This is the exergy change of the air stored in the tank.
Thus, the change in exergy of the air stored in the tank is
Want to see more full solutions like this?
Chapter 8 Solutions
THERMODYNAMICS (LL)-W/ACCESS >CUSTOM<
- Can you solve it analytically using laplace transforms and with Matlab code as well please. Thank You.arrow_forwardQ11. Determine the magnitude of the reaction force at C. 1.5 m a) 4 KN D b) 6.5 kN c) 8 kN d) e) 11.3 KN 20 kN -1.5 m- C 4 kN -1.5 m B Mechanical engineering, No Chatgpt.arrow_forwardplease help with this practice problem(not a graded assignment, this is a practice exam), and please explain how to use sohcahtoaarrow_forward
- Solve this problem and show all of the workarrow_forwardSolve this problem and show all of the workarrow_forwardaversity of Baoyion aculty of Engineering-AIMusyab Automobile Eng. Dep. Year: 2022-2023, st Course, 1st Attempt Stage: 3rd Subject: Heat Transfer I Date: 2023\01\23- Monday Time: 3 Hours Q4: A thick slab of copper initially at a uniform temperature of 20°C is suddenly exposed to radiation at one surface such that the net heat flux is maintained at a constant value of 3×105 W/m². Using the explicit finite-difference techniques with a space increment of Ax = = 75 mm, determine the temperature at the irradiated surface and at an interior point that is 150 mm from the surface after 2 min have elapsed. Q5: (12.5 M) A) A steel bar 2.5 cm square and 7.5 cm long is initially at a temperature of 250°C. It is immersed in a tank of oil maintained at 30°C. The heat-transfer coefficient is 570 W/m². C. Calculate the temperature in the center of the bar after 3 min. B) Air at 90°C and atmospheric pressure flows over a horizontal flat plate at 60 m/s. The plate is 60 cm square and is maintained at a…arrow_forward
- University of Baby on Faculty of Engineering-AIMusyab Automobile Eng. Dep. Year: 2022-2023. 1 Course, 1" Attempt Stage 3 Subject Heat Transfer I Date: 2023 01 23- Monday Time: 3 Hours Notes: Q1: • • Answer four questions only Use Troles and Appendices A) A flat wall is exposed to an environmental temperature of 38°C. The wall is covered with a layer of insulation 2.5 cm thick whose thermal conductivity is 1.4 W/m. C, and the temperature of the wall on the inside of the insulation is 315°C. The wall loses heat to the environment by convection. Compute the value of the convection heat-transfer coefficient that must be maintained on the outer surface of the insulation to ensure that the outer-surface temperature does not exceed 41°C. B) A vertical square plate, 30 cm on a side, is maintained at 50°C and exposed to room air at 20°C. The surface emissivity is 0.8. Calculate the total heat lost by both sides of the plate. (12.5 M) Q2: An aluminum fin 1.5 mm thick is placed on a circular tube…arrow_forwardSolve using graphical method and analytical method, only expert should solvearrow_forwardSolve this and show all of the workarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY