Repeat Prob. 8–114 if heat were supplied to the pressure cooker from a heat source at 180°C instead of the electrical heating unit?
8–114 A 4-L pressure cooker has an operating pressure of 175 kPa. Initially, one-half of the volume is filled with liquid water and the other half by water vapor. The cooker is now placed on top of a 750-W electrical heating unit that is kept on for 20 min. Assuming the surroundings to be at 25°C and 100 kPa, determine (a) the amount of water that remained in the cooker and (b) the exergy destruction associated with the entire process.
FIGURE P8–114
(a)
The final mass of water that remained in the cooker.
Answer to Problem 120RP
The final mass of water that remained in the cooker is
Explanation of Solution
Express the mass balance for a pressure cooker which acts as a system.
Here, initial mass is
Write an energy balance for a system.
Here, internal energy at state 1 and 2 is
Calculate the initial mass in the tank
Here, saturated liquid specific volume is
Calculate the initial internal energy
Here, specific internal energy of saturated fluid is
Calculate the initial entropy
Here, specific entropy of saturated fluid is
Write the internal energy at state 2
Here, dryness fraction at state 2 is
Write the specific volume at state 2
Write the formula to calculate the mass of the water remained in tank
Here, volume of the cooker is
Conclusion:
From the Table A-5 of “Saturated water: Pressure”, obtain the saturated liquid specific volume
From the Table A-5 of “Saturated water: Pressure”, obtain the enthalpy
Since one half of the volume is filled with liquid water and other half by water vapor, calculate the volume of tank
Substitute
Substitute 1.893 kg for
Substitute 1.893 kg for
Substitute
Substitute
Re-write the Equation (II) using the Equation (I),
Substitute
Substitute
Substitute 0.001918 for
Substitute
Thus, the final mass of water that remained in the cooker is
(b)
The amount of exergy destructed during the heat supplied to pressure cooker from heat source.
Answer to Problem 120RP
The amount of exergy destructed during the heat supplied to pressure cooker from heat source is
Explanation of Solution
For an extended system, write the simplification rate form of the entropy balance.
Here, entropy generation is
Calculate the exergy destroyed during the process
Here, dead state temperature is
Substitute Equation (XI) in Equation (XII).
Calculate the entropy at state 2
Conclusion:
Substitute 0.001918 for
Substitute 1.8945 kg for
Substitute 298 K for
Thus, the amount of exergy destructed during the heat supplied to pressure cooker from heat source is
Want to see more full solutions like this?
Chapter 8 Solutions
EBK THERMODYNAMICS: AN ENGINEERING APPR
- An air conditioner with refrigerant-134a as the refrigerant is used to keep a large space at 20°C by rejecting the waste heat to the outside air at 37 °C. The room is gaining heat through the walls and the windows at a rate of 125 kJ/min while the heat generated by the computer, TV, and lights amounts to 0.7 kW. Unknown amount of heat is also generated by the people in the room. The condenser and evaporator pressures are 1200 and 500 kPa, respectively. The refrigerant is saturated liguid at the condenser exit and saturated vapor at the compressor inlet. If the refrigerant enters the compressor at a rate of 65 L/min and the isentropic efficiency of the compressor is 70%, determine (a) the temperature of the refrigerant at the compressor exit, (b) the rate of heat generated by the people in the room, (c) the COP of the air conditioner, and (d) the minimum volume flow rate of the refrigerant at the compressor inlet for the same compressor inlet and exit conditions.arrow_forwardRefrigerant R-134a enters the compressor of a refrigeration machine at 140 kPa pressure and -10°C temperature and exits at 1 MPa pressure. The volumetric flow of the refrigerant entering the compressor is 0.23 m3/minute. The refrigerant enters the throttling valve at 0.95 MPa pressure and 30°C, exiting the evaporator as saturated steam at -18°C. The adiabatic efficiency of the compressor is 78%. Show the cycle in the T-s diagram. a) Calculate the power required to start the compressor. b) Calculate the heat taken in a unit time from the cooled environment. COP=? c) Calculate between the evaporator and the compressor, how much the pressure of the refrigerant drops, and how much is the heat gain.arrow_forwardA boiler produces 5.4 tonnes/hour of steam at a pressure of 1.5 MPa and a temperature of 350°C. Feedwater enters at a temperature of 44.5°C. At exit from the economizer part of the boiler the temperature is 93.5°C. At exit from the evaporator part of the boiler the steam is 90 A % dry. Energy is supplied by 600 kg of coal per hour, which has a calorific value of 32 MJ/kg. The A/F ratio is 15 1. The temperature of the flue gas at exit from the the economizer part of the boiler is 210°C. The average specific heat at constant pressure of the in the economizer is 1045 J/kg.K. When the ambient temperature is 24°C : 7. IS flue gas 7.1 Calculate the efficiency of the boiler. [83.3 %] Calculate the equivalent evaporation from and at 100°C per unit mass of fuel. |11.9| Draw up an energy balance, on a kJ/kg coal basis, with percentages of the total energy supplied. Jeconomizer 6.8 %, evaporator 62 %, superheater 15.5 %, to atmosphere 9.7 %, other 7.2 7.3 losses 7 %]arrow_forward
- THERMOFLUID In steam power plants, open feedwater heaters are frequently utilized to heat the feedwater by mixing it with steam bled off the turbine at some intermediate stage. Consider an open feedwater heater that operates at a pressure of 1000 kPa. Feedwater at 50°C and 1000 kPa is to be heated with superheated steam at 200°C and 1000 kPa. In an ideal feedwater heater, the mixture leaves the heater as saturated liquid at the feedwater pressure. Determine the ratio of the mass flow rates of the feedwater and the superheated vapor for this case.arrow_forward1. A Carnot heat engine receive 1200 kJ of heat per cycle from a high-temperature reservoir at 420 °C and reject heat to a low-temperature reservoir at 35 °C. Determine the thermal efficiency of this Carnot engine, the maximum work produced and the amount of heat rejected to the low temperature reservoir. II. A 1-m³ tank containing air at 25°C and 500 Kpa (abs) is connected through a valve to another tank containing 5 kg of air at 35°C and 200 Kpa (abs). Now the valve is opened, and the system is allowed to reach thermal equilibrium, which are at 20 °C. Determine the volume of the second tank and the final equilibrium pressure of air.arrow_forwardAn air refrigeration system having pressure ratio of 5 takes air at 0°C and 1 atm. It is compressed and then cooled to 19°C. A pressure drop of 5 kPa is measured in both cooler and refrigerator. If the efficiency of the compressor is 95% and that of the expander is 75%, determine the refrigeration capacity of the system TR, and the COP of the system if the flow of air is 7.5 kg/min. Assume compression and expansion processes to be isentropic.arrow_forward
- Solve the following problems: Note: Draw the p-h diagram completely labeling the respective refrigerant conditions (pressures and temperatures) and define the properties of refrigerant (enthalpies and specific volume) needed to solve the respective problems. In an ammonia refrigeration system, the capacity is (1) 210 kW at a temperature of-20°C. The vapor from the evaporator is pumped by one compressor to the condensing pressure of 1431 kPa. Later, the system was revised to a two-stage compression operating on the cycle shown below with intercooling but no removal of flash at 555 kPa. (а) Calculate the power required by the single compressor in the original system. (b) Calculate the total power required by the two compressors in the revised system. Condenser 1431kPa High-stage compressor Intercooler 555kPa Evaporator 2í0kW -20°C Low-stage compresaorarrow_forwardA refrigeration plant works between the temperatures limits of -5°C and 25°C. The refrigerant is CO2 is wet at the entry to the compressor and has dryness fraction of 0.6. The refrigerator has actual COP 70% of the theoretical COP. If there is no under-cooling, determine the ice formed during a period of 24 hours from 20°C. The mass of CO2 circulated is 5kg/min. Take enthalpy of fusion of ice as 336 kJ/kg. The properties of CO2 are as follows: Saturation temperature (C°) Specific enthalpy (kJ/kg) hf Specific entropy (kJ/kg-K) hg Sf 25 81.25 202.75 0.2513 -5 -7.53 238.5 -0.04187arrow_forwardIn steam power plants, open feedwater heaters are frequently utilized to heat the feedwater by mixing it with steam bled off the turbine at some intermediate stage. Consider an open feedwater heater that operates at a pressure of 1200 kPa. Feedwater at 50°C and 1200 kPa is to be heated with superheated steam at 200°C and 1200 kPa. In an ideal feedwater heater, the mixture leaves the heater as saturated liquid at the feedwater pressure. Determine the ratio of the mass flow rates of the feedwater and the superheated vapor for this case.arrow_forward
- 15- R134a enters a compressor with a heat loss of 200 W as saturated steam at -24 ºC and after compressing to 0.8 MPa, it exits the compressor at 60 ºC. The mass flow of R134a is 1.2 kg/s. Calculate the volumetric flow of the refrigerant at the compressor inlet. A-0,129 m3/sB-0,293 m3/sC-0,163 m3/sD-0,209 m3/sE- 0,347 m3/s (Note: This Turkish I'm using translate) orginal; R134a ısı kaybı 200 W olan bir kompresöre doymuş buhar olarak -24 ºC sıcaklıkta girmekte ve 0.8 MPa basınca sıkıştırıldıktan sonra kompresörden 60 ºC sıcaklıkta çıkmaktadır. R134a’nın kütlesel debisi 1.2 kg/s’dir.Soğutucu akışkanın kompresör girişindeki hacimsel debisini hesaplayınız.arrow_forwardplease include all stepsarrow_forwardA rigid tank of 0.22-m'volume initially contains saturated vapor refrigerant-134a at 1.2 MPa. The tank is connected by a valve to a supply line that carries refrigerant-134a at 1.6 MPa and 46 C. The valve is opened, and the refrigerant is allowed to enter the tank. The valve is closed when it is observed that the tank contains saturated liquid at 1.6 MPa. Determine (a) the mass of the refrigerant that has entered the tank and (b) the amount of heat transfer.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY