Derive the equation P = ( W r a ) tan ( θ + ϕ s ) , to raise the load.

Question

Want to see the full answer?

Answer 1

Question

Chapter 8.2, Problem 8.68P

(a)

To determine

Derive the equation P=(Wra)tan(θ+ϕs), to raise the load.

(b)

To determine

Derive the equation P=(Wra)tan(ϕs−θ), to lower the load.

(c)

To determine

Derive the equation P=(Wra)tan(θ−ϕs), to hold the load.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

Quiz/An eccentrically loaded bracket is welded to the support as shown in Figure below. The load is static. The weld size for weld w1 is h1 = 4mm, for w2 h2 = 6mm, and for w3 is h3 =6.5 mm. Determine the safety factor (S.f) for the welds. F=29 kN. Use an AWS Electrode type (E100xx). 163 mm S 133 mm 140 mm Please solve the question above I solved the question but I'm sure the answer is wrong the link : https://drive.google.com/file/d/1w5UD2EPDiaKSx3W33aj Rv0olChuXtrQx/view?usp=sharing

Q2: (15 Marks) A water-LiBr vapor absorption system incorporates a heat exchanger as shown in the figure. The temperatures of the evaporator, the absorber, the condenser, and the generator are 10°C, 25°C, 40°C, and 100°C respectively. The strong liquid leaving the pump is heated to 50°C in the heat exchanger. The refrigerant flow rate through the condenser is 0.12 kg/s. Calculate (i) the heat rejected in the absorber, and (ii) the COP of the cycle. Yo 8 XE-V lo 9 Pc 7 condenser 5 Qgen PG 100 Qabs Pe evaporator PRV 6 PA 10 3 generator heat exchanger 2 pump 185 absorber

Q5:(? Design the duct system of the figure below by using the balanced pressure method. The velocity in the duct attached to the AHU must not exceed 5m/s. The pressure loss for each diffuser is equal to 10Pa. 100CFM 100CFM 100CFM ☑ ☑ 40m AHU -16m- 8m- -12m- 57m 250CFM 40m -14m- 26m 36m ☑ 250CFM

Answer 2

Question

Chapter 8.2, Problem 8.68P

(a)

To determine

Derive the equation P=(Wra)tan(θ+ϕs), to raise the load.

(b)

To determine

Derive the equation P=(Wra)tan(ϕs−θ), to lower the load.

(c)

To determine

Derive the equation P=(Wra)tan(θ−ϕs), to hold the load.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 3

Question

Chapter 8.2, Problem 8.68P

(a)

To determine

Derive the equation P=(Wra)tan(θ+ϕs), to raise the load.

(b)

To determine

Derive the equation P=(Wra)tan(ϕs−θ), to lower the load.

(c)

To determine

Derive the equation P=(Wra)tan(θ−ϕs), to hold the load.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 4

Question

Chapter 8.2, Problem 8.68P

(a)

To determine

Derive the equation P=(Wra)tan(θ+ϕs), to raise the load.

(b)

To determine

Derive the equation P=(Wra)tan(ϕs−θ), to lower the load.

(c)

To determine

Derive the equation P=(Wra)tan(θ−ϕs), to hold the load.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 5

Chapter 8.2, Problem 8.68P

(a)

To determine

Derive the equation P=(Wra)tan(θ+ϕs), to raise the load.

(b)

To determine

Derive the equation P=(Wra)tan(ϕs−θ), to lower the load.

(c)

To determine

Derive the equation P=(Wra)tan(θ−ϕs), to hold the load.

Answer 6

Chapter 8.2, Problem 8.68P

(a)

To determine

Derive the equation P=(Wra)tan(θ+ϕs), to raise the load.

Answer 7

Chapter 8.2, Problem 8.68P

(a)

To determine

Derive the equation P=(Wra)tan(θ+ϕs), to raise the load.

Answer 8

(b)

To determine

Derive the equation P=(Wra)tan(ϕs−θ), to lower the load.

Answer 9

(b)

To determine

Derive the equation P=(Wra)tan(ϕs−θ), to lower the load.

Answer 10

(c)

To determine

Derive the equation P=(Wra)tan(θ−ϕs), to hold the load.

Answer 11

(c)

To determine

Derive the equation P=(Wra)tan(θ−ϕs), to hold the load.

Answer 12

Expert Solution & Answer

Answer 13

Expert Solution & Answer

Answer 14

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 15

Ch. 8.1 - Knowing that the coefficient of friction between...Ch. 8.1 - Two blocks A and B are connected by a cable as...Ch. 8.1 - A cord is attached to and partially wound around a...Ch. 8.1 - A 40-kg packing crate must be moved to the left...Ch. 8.1 - Determine whether the block shown is in...Ch. 8.1 - Determine whether the block shown is in...Ch. 8.1 - Determine whether the block shown is in...Ch. 8.1 - Determine whether the block shown is in...Ch. 8.1 - Knowing that = 45 in Prob. 8.1, determine the...Ch. 8.1 - The 20-lb block A hangs from a cable as shown....

Derive the equation P = ( W r a ) tan ( θ + ϕ s ) , to raise the load.

Solution Summary: The author illustrates how the equation has been derived, and the free-body diagram of the jack handle.

Concept explainers

Videos

Derive the equation P=(Wra)tan(θ+ϕs), to raise the load.

Derive the equation P=(Wra)tan(ϕs−θ), to lower the load.

Derive the equation P=(Wra)tan(θ−ϕs), to hold the load.

Want to see the full answer?

Chapter 8 Solutions