ELECTRICITY FOR TRADES
3rd Edition
ISBN: 9780078118630
Author: Petruzella
Publisher: RENT MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 8.1, Problem 10RQ
In what way is the construction of an adjustable resistor different from that of a fixed resistor?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Matched filter in the frequency domain
(1.5) (a) Consider the signal s(t) in 3(c). Assuming that the unit of time is a millisecond
and the desired frequency resolution is 1 Hz, use the function contFT to compute
and plot |S(f).
(b) Use the function contFT to compute and plot the magnitude of the Fourier trans-
form of the convolution s * SMF numerically computed in 3(d). Also plot for
comparison |S(f)12, using the output of 5(a). The two plots should match.
(c) Plot the phase of the Fourier transform of s✶ SMF obtained in 5(b). Comment on
whether the plot matches your expectations.
Find Eigenvalues and Eigenvectors for the following matrices:
[10
4
A=0
2
0
3
1
1 -3
1. (20 pts) Plot the pulse and the FFT for a pulse with the following properties at x=0 and x=10
cm.
f=2 MHz
m=3
Ncyc=2, 6, 20
po 1 MPa (source pressure)
x=10 cm (propagates in a Newtonian fluid for 10 cm as a plane wave-not a sound beam)
a=0.5 dB/(MHz cm)
Consider 3 types of waves: sine, square, and sawtooth. (square and sawtooth only for grad
students)
Observe your plots and draw some conclusions. Discuss any possible issues you encounter.
2. (20 pts) We have the following 3 ultrasonic transducers:
a. Focused 1 MHz, 2.54 cm diameter, 5.08 cm focus
b. Focused 3 MHz, 2.54 cm diameter, 5.08 cm focus
c. Unfocused 0.1 MHz, 2.54 cm diameter
The transducers are operating in water (c=1486 m/s).
I. Plot the axial field for all transducers
II. Plot the focal transverse field for the focused transducers and the transverse field at the
Rayleigh distance (R_0) and at 2R_0 for the unfocused.
III. Assume source pressure of 0.1 MPa, and find the acoustic pressure in MPa at the location
(r=0, z=4.5…
Chapter 8 Solutions
ELECTRICITY FOR TRADES
Ch. 8.1 - In what way is resistance wire different from the...Ch. 8.1 - What is the trade name for the most popular type...Ch. 8.1 - Prob. 3RQCh. 8.1 - Name the three ways by which resistors are rated.Ch. 8.1 - Resistors are classified as passive devices. Why?Ch. 8.1 - Identify the type of circuit that generally...Ch. 8.1 - State two functions served by a fusible resistor.Ch. 8.1 - What advantage do film resistors have over...Ch. 8.1 - What are the two configurations for chip...Ch. 8.1 - In what way is the construction of an adjustable...
Ch. 8.1 - Compare the connection and control function of a...Ch. 8.1 - If the wiper arm of a linear potentiometer is...Ch. 8.1 - Explain how a 10-turn trim pot is adjusted.Ch. 8.1 - Compare the way the resistance varies in a linear...Ch. 8.1 - Identify the color bands for each of the following...Ch. 8.1 - A 680- resistor has a rated tolerance of 10...Ch. 8.1 - What is the color code for a 365- five-band...Ch. 8.1 - Determine the resistance value and percentage of...Ch. 8.1 - Determine the resistance value and percentage of...Ch. 8.2 - Calculate the total resistance for each of the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Find the Q-points for the diodes in the circuit. Assume ideal diodes, and startwith the assumption that D is OFF, and D2 is ON for both circuits.arrow_forwardplease see the following image to answer questions thanksarrow_forward5- Find the Eigenvalues and the corresponding Eigenvectors. [4 5 31 A=0 4 6 Lo 0 1arrow_forward
- Find the Eigenvalues and the corresponding Eigenvectors. 4 2 -2 A = 2 5 0,2=4 -2 -2 0 3arrow_forward1. Label the x, y, z coordinates for each frame. 2. Compute the homogeneous transformation matrices H between frames 0, 1, 2, and end- effector.arrow_forwardFind Eigenvalues and Eigenvectors for the following matrices: 1] [5-6 A = 1 1 0 L3 0 1arrow_forward
- Use Gauss-Jordan Elimination method to solve the following system: 4x1+5x2 + x3 = 2 x1-2x2 3x3 = 7 - 3x1 x2 2x3 = 1. -arrow_forwardFind the Eigenvalues and the corresponding Eigenvectors. A = [³/2 9] 3.arrow_forwardFind the Q-points for the diodes in the circuit. Assume ideal diodes, and startwith the assumption that both diodes are ON for both circuits.arrow_forward
- I need help with the PSpice part. How do I do the PSpice stuff.arrow_forwardUse Gauss-Jordan Elimination method to solve the following system: 4x1 +5x2 + x3 = 2 x1-2x2 3x3 = 7 - 3x1 x2 2x3 = 1. -arrow_forwardNo need to solve question 1. Only work on question 2 where you make the PSpice model for this circuit. I need the basic step by step to find what is wanted in question 1. Explain what kind of analysis is used and what details are adjusted in it. Also explain/perform gathering the data on a plot for the simulation.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
Kirchhoff's Rules of Electrical Circuits; Author: Flipping Physics;https://www.youtube.com/watch?v=d0O-KUKP4nM;License: Standard YouTube License, CC-BY