Answered: A steel band exerts a horizontal force…

A steel band exerts a horizontal force of 80.0 N on a tooth at point B in Figure P8.2. What is the torque on the root of the tooth about point A? Gum 48.0° B 1.20 cm

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A uniform, 267 N rod that is 2.06 mm long carries a 225 N weight at its right end and an unknown weight WW toward the left end (see the figure below). When WW is placed 55.9 cm from the left end of the rod, the system just balances horizontally when the fulcrum is located 74.7 cm from the right end. a. What is w (in N)? b. If the weight w is moved 25.3 cm to the right, how far must the fulcrum (balance point) be moved to restore balance? 225 N Figure 1. A mass rests on the left side of a balance beam.
1. The drawing shows the top view of a door that is 2 m wide. Two forces are applied to the door as indicated in the figure. What is the magnitude of the net torque on the door with respect to the hinge? 10 N 60° hinge 1 m 60° 10 N
A wrench 0.8 meters long lies along the positive y-axis, and grips a bolt at the origin. A force is applied in the direction of (0,-1,-3) at the end of the wrench. Find the magnitude of the force in newtons needed to supply 100 newton-meters of torque to the bolt. Force: newtons
A pipe system consists of three pipes with lengths = 1.50 m, L2 L1 0.500 m, and L3 2.60 m. A plumber pulls on the end of the pipe system, at the point P, with a force Fp = -21.0 Ni+ 49.0 Nj + 31.5 Nk. L, What is the torque 7 due to Fp about the origin? そ= N•m Enter your expression using ijk unit vector notation.
A circular disk with a radius of 0.42 m is subject to 2 tangentially applied forces. The disc is fixed such that it will rotate about its center. Both forces produce a torque in the same direction. F1 = 4.4 N applied at the outer edge of the disc. F2 = 3 N applied at a distance of 0.2 from the center of the disc. What is the net torque on the disc?
When you bend over, a series of large muscles, the erector spinae, pull on your spine to hold you up. Figure shows a simplified model of the spine as a rod of length L that pivots at its lower end. In this model, the center of gravity of the 320 N weight of the upper torso is at the center of the spine. The 160 N weight of the head and arms acts at the top of the spine. The erector spinae muscles are modeled as a single muscle that acts at an 12° angle to the spine. Suppose the person shown bends over to an angle of 30° from the horizontal. a. What is the tension in the erector muscle? Hint: Align your x-axis with the axis of the spine.b. A force from the pelvic girdle acts on the base of the spine. What is the component of this force in the direction of the spine? (This large force is the cause of many back injuries).
Wolverine has an arm that is 1[m] long and claws that are 0.5[m] long. He's trying to knock over a wall. His shoulder can exert a torque of 1,500[N-m]. What is the ratio of force on the wall with vs without his claws extended? 1.5[m] point Pivot F /F Adamantium Wall without with claws claws A. 2/3 F Wolverine with В. 3/2 with claws С. 1 1.0[m] Pivot Adamantium D. I don't know but the torque direction is point Wall E. I don't know but the torque direction is Fwithout Wolverine Bare hands
A flagpole has a uniform mass density and total mass of M and length L. It is hinged at the ground and makes an angle of U with respect to the horizontal, as shown. To support the pole, a horizontal cable is attached to the pole at a point L from the bottom of the pole. 3 What is the correct sum of torque equation for the axis perpendicular to the page and passing through the bottom of the pole? cable 2L/3 0-Mg + 흙LT=0 O-Mgcos0 +LTsin0 = 0 ○ 들Mgsind + 능TCOS6) +Tcose = 0 Mgsino + LTcos0 = 0 O- Mgsin0+LTcos0 = 0
In unit-vector notation, what is the net torque about the origin on a flea located at coordinates (0, -4.30 m, 7.74 m) when forces F = (3.80 N )k and F = (-7.82 N )Ĵ act on the flea? 2 Number i î i i k Units
Please ASAP
A 10.0 m long rod, with a mass which acts at its center, supports three weights as shown. Where is its center of gravity? X kg Y kg 0.0 5.0 m Z kg 10.0 m where X = 5.00, Y = 15.0, and Z=30.0.
The fishing pole in the figure below makes an angle of 20.0° with the horizontal. What is the magnitude of the torque exerted by the fish about an axis perpendicular to the page and passing through the angler's hand if the fish pulls on the fishing line with a force F = 125 N at an angle 37.0° below the horizontal? The force is applied at à point L = 1.92 m from the angler's hands. N.m -I 20.0° 37.0 1 20.0° F