Answered: 10.0 N 30.0 12.0 N b. 9.00 N Consider… | bartleby

Related questions

Question

100%

10.0 N
30.0°
12.0 N
9.00 N
Consider the figure above, which shows a brass axle of radius a attached to an
aluminum wheel of radius b. What is the total Torque on the device about an axis
passing through the brass axle at O?? Assume that the positive direction is into the
page.
Here, you should assume the following quantities: a = 5.7 cm and b = 30.0 cm.
Express your answer in N-m.
%3D

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A kitchen door is attached to a vertical support by a set of hinges. Assume the door is uniform and has height 2.40 m, width 0.865 m, and mass 21.0 kg. A. Determine its moment of inertia (in kg · m2) for rotation on its hinges. B. Are any pieces of data unnecessary? (Select all that apply.) The height of the door is unnecessary. The width of the door is unnecessary. The mass of the door is unnecessary. No; all of the data are necessary.
The fishing pole in the figure below makes an angle of 20.0° with the horizontal. What is the magnitude of the torque exerted by the fish about an axis perpendicular to the page and passing through the angler's hand if the fish pulls on the fishing line with a force F = 125 N at an angle 37.0° below the horizontal? The force is applied at à point L = 1.92 m from the angler's hands. N.m -I 20.0° 37.0 1 20.0° F
Plz use g = 9.8 m/s2 to find if needed
A rectangular bar is hinged at point O. The bar is 3.00 m long and 2.00 m wide. Find the torque resulting from the following force about an axis through point O: F1 = 1 N. Use a positive for a counterclockwise torque and a negative for a clockwise torque.
A bug is on the surface of a small wheel, which is a solid disk.
A long, thin uniform rod of length 1.29m and mass 2.08kg is pivoted about a horizontal, frictionless pin passing through one end. The rod is released from one end in the vertical position. L y Pivot x At the instant the rod is horizontal, find its angular speed. Submit Answer Tries 0/10 At the instant the rod is horizontal, what is its angluar acceleration? Submit Answer Tries 0/10 At the instant the rod is horizontal, what is the magnitude of its x-component of acceleration at its centre of mass? Submit Answer Tries 0/10 At the instant the rod is horizontal, what is the magnitude of its Y-component of acceleration at its centre of mass? Submit Answer Tries 0/10
Calculate the net torque about this axis due to the three forces shown in the figure if the magnitudes of the forces are F1 = 27.0 N, F2 = 16.7 N, and F3 = 14.9 N. The plate and all forces are in the plane of the page. Take positive torques to be counterclockwise.
Computation. A uniform solid sphere has mass M = 8.9 kg and radius R = 0.2 m. What is its moment of inertia about an axis tangent to its surface? I- 2 kg .m² Record your your numerical answer below, assuming three significant figures. Remember to include a as necessary.
Baby Huey rolls a hollow sphere of mass M and radius R up a hillside, giving it an initial kinetic energy of Ki. It rolls over the top of the hill of height h and keeps going. The ball rolls without slipping the whole way, but it loses Wnc due to non-conservative forces between the foot of the hill and the top. a. If M = 6.82 kg and R = 10.9 cm, find its rotational inertia. b. Find the translational velocity at the top of the hill.
A solid disk with an axis of rotation through the center (perpendicular to the diagram). Two holes are cut out near the center and the material is placed near the rim. Which has the larger I? Please explain your conclusion.
A pipe system consists of three pipes with lengths L1 = 1.95 m, L2 = 0.500 m, and L3 = 2.90 m. A plumber pulls on the end of the pipe system, at the point P, with a force Fp = -23.0 Ni+ 42.0 Nj + 32.0 Nk. Po What is the torque 7 due to about the origin? Enter your expression using ijk unit vector notation. N-m
A mass of 0.8 kg is located at the end of a very light and rigid rod 50 cm in length. The rod is rotating about an axis at its opposite end with a rotational velocity of 3 rad/s.a. What is the rotational inertia of the system?b. What is the angular momentum of the system? USe the correct formula to solve and get the right answr.

SEE MORE QUESTIONS