A flagpole has a uniform mass density and total mass of M and length L. It is hinged at the groundand makes an angle of U with respect to the horizontal, as shown. To support the pole, a horizontalcable is attached to the pole at a point L from the bottom of the pole.3What is the correct sum of torque equation for the axis perpendicular to the page and passingthrough the bottom of the pole?cable2L/30-Mg + 흙LT=0O-Mgcos0 +LTsin0 = 0○ 들Mgsind + 능TCOS6)+Tcose = 0Mgsino + LTcos0 = 0O-Mgsin0+LTcos0 = 0

Answered: Image /qna-images/answer/c30ec921-983d-45bf-88ac-31923a697949.jpg

Answered: A flagpole has a uniform mass density…

Similar questions

You push on the door as shown in the drawing. Calculate the torque experienced at the door hinge.
When opening a door, you push on it perpendicularly with a force of 48 N at a distance of 1.2m from the hinges. What torque are you exerting relative to the hinge?
On the basis of second condition of equilibrium. When opening a door, you push on it perpendicularly with a force of 55.0 N at a distance of 0.850m from the hinges. What torque are you exerting relative to the hinges?
(a) When opening a door, you push on it perpendicularly with a force of 44.0 N at a distance of 0.780 m from the hinges. What torque (in N-m) are you exerting relative to the hinges? (Enter the magnitude.) N-m (b) Does it matter if you push at the same height as the hinges? O Yes O No
Consider an unsuccessful attempt to take off a tire using a wrench to loosen the bolts. Assume the wrench is 0.3m long and are you able to apply a 200N force Because the tire is flat you can only apply your force at a 60° angle. What is the torque at the center of the bolt. You find a tire jack and are now able to apply 200N of force at an 80° angle. Is the resulting torque more or less and what is the new torque.
Calculate the net torque about point O for the three forces (F₁=15.7 N, F₂=17.8 N and F3-20 N) applied on the rod as shown in the figure, where =25.2°. The rod and all forces are in the plane of the page. Assume the z-axis to be the axis perpendicular to the page. -12.0 m- 13.00 m 90.0⁰ 00 F₁ -4.00m- F2 10.3 m.N, about the z-axis 147 m.N, about the z-axis -66.5 m-N, about the z-axis 308 m.N, about the z-axis F3
Problem#4: А thin and light rod with 7-ft length is resting horizontally on a pivot through a point 2.5 ft from the left end. To maintain the balance and avoid a rotational motion of the rod, a 23 is hung is applied the right end downwards at the left end. Calculate the force applied at the left end lbs block at and another force and the normal force exerted by the pivot on the rod.
Two forces are applied to a door. Both forces are applied at the door knob, and both forces have the same magnitude. The first force is applied perpendicular to the door, and the second force is applied at 15 degrees to the plane of the door. Which force exerts the greater torque about the door hinge?
A force, T, is exerted on a horizontal beam at point B at an angle 8 with respect to the horizontal as shown. The magnitude of the torque created by force T about point C, is given by E A AT B W₁ O W₁
A 81 cm wide door is pushed open with a 91N force applied to the end opposite the hinges. For each of the following, calculate the torque about an axis that passes through the hinges. a)The force is applied at 250 from the perpendicular to the face of the door, toward the hinges. b) The force is applied at 700 from the perpendicular to the face of the door, toward the hinges.
A person exerts a horizontal force of 30 N on the end of a door 92 cm wide. a) What is the magnitude of the torque if the force is exerted perpendicular to the door? b) What is the magnitude of the torque if the force is exerted at a 70.0 ∘ angle to the face of the door?