When boiling water a hot plate takes an average of 8 minutes [min] and 55 seconds [s] to boil 100 milliliters [mL] of water. Assume the temperature in the lab is 75 degrees Fahrenheit [°F]. The hot plate is rated to provide 283 watts [W], If we wish to boil 100 milliliters [mL] of acetone using this same hot plate, how long do we expect the process to take? Acetone has a boiling point of 56 degrees Celsius [°C], The specific heat capacity of water is 4.18 joules per gram degree Celsius [J/(g °C)]. Acetone has a specific gravity of 0.785 and a specific heat capacity of 2.15 joules per gram degree Celsius [J/(g °C)]. [ Hint: You must determine the efficiency of the hotplate.]
When boiling water a hot plate takes an average of 8 minutes [min] and 55 seconds [s] to boil 100 milliliters [mL] of water. Assume the temperature in the lab is 75 degrees Fahrenheit [°F]. The hot plate is rated to provide 283 watts [W], If we wish to boil 100 milliliters [mL] of acetone using this same hot plate, how long do we expect the process to take? Acetone has a boiling point of 56 degrees Celsius [°C], The specific heat capacity of water is 4.18 joules per gram degree Celsius [J/(g °C)]. Acetone has a specific gravity of 0.785 and a specific heat capacity of 2.15 joules per gram degree Celsius [J/(g °C)]. [ Hint: You must determine the efficiency of the hotplate.]
Solution Summary: The author calculates the time taken by the process to heat the acetone.
When boiling water a hot plate takes an average of 8 minutes [min] and 55 seconds [s] to boil 100 milliliters [mL] of water. Assume the temperature in the lab is 75 degrees Fahrenheit [°F]. The hot plate is rated to provide 283 watts [W], If we wish to boil 100 milliliters [mL] of acetone using this same hot plate, how long do we expect the process to take? Acetone has a boiling point of 56 degrees Celsius [°C], The specific heat capacity of water is 4.18 joules per gram degree Celsius [J/(g °C)]. Acetone has a specific gravity of 0.785 and a specific heat capacity of 2.15 joules per gram degree Celsius [J/(g °C)]. [Hint: You must determine the efficiency of the hotplate.]
oyfr
3. The figure shows a frame under the
influence of an external loading made up
of five forces and two moments. Use the
scalar method to calculate moments.
a. Write the resultant force of the
external loading in Cartesian vector
form.
b. Determine the
& direction
of the resultant moment of the
external loading about A.
15 cm
18 cm
2.2 N-m
B
50 N
45°
10 cm
48 N.m
250 N
60 N
20
21
50 N
25 cm
100 N
A
118,
27cm 5, 4:1
The 2-mass system shown below depicts a disk which rotates about its center and has rotational
moment of inertia Jo and radius r. The angular displacement of the disk is given by 0. The spring
with constant k₂ is attached to the disk at a distance from the center. The mass m has linear
displacement & and is subject to an external force u. When the system is at equilibrium, the spring
forces due to k₁ and k₂ are zero. Neglect gravity and aerodynamic drag in this problem. You may
assume the small angle approximation which implies (i) that the springs and dampers remain in
their horizontal / vertical configurations and (ii) that the linear displacement d of a point on the
edge of the disk can be approximated by d≈re.
Ө
K2
www
m
4
Cz
777777
Jo
Make the following assumptions when analyzing the forces and torques:
тв
2
0>0, 0>0, x> > 0, >0
Derive the differential equations of motion for this dynamic system. Start by sketching
LARGE and carefully drawn free-body-diagrams for the disk and the…
A linear system is one that satisfies the principle of superposition. In other words, if an input u₁
yields the output y₁, and an input u2 yields the output y2, the system is said to be linear if a com-
bination of the inputs u = u₁ + u2 yield the sum of the outputs y = y1 + y2.
Using this fact, determine the output y(t) of the following linear system:
given the input:
P(s) =
=
Y(s)
U(s)
=
s+1
s+10
u(t) = e−2+ sin(t)
=e
Chapter 8 Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY