Aggregate Functions: SQL has some built-in functions and they are called as aggregate functions. SQL contains five built-in functions. They are: SUM – This function is used to add values from the particular column. Syntax: SELECT SUM(column_Name) FROM table_Name; COUNT – This is used to count the number of rows for the particular column. Syntax: SELECT COUNT(column_Name) FROM table_Name; MAX – This function is used to get the maximum value from the column. Syntax: SELECT MAX(column_Name) FROM table_Name; MIN – This function is used to get the minimum value from the column. Syntax: SELECT MIN(column_Name) FROM table_Name; AVG – This function is used to get the average of all the values from the column. Syntax: SELECT AVG(column_Name) FROM table_Name; DISTINCT Keyword: “DISTINCT” keyword is used to avoid redundant data (removing duplicate values) from a column. The syntax for “DISTINCT” keyword is as follows: SELECT DISTINCT column_Name FROM table_Name;

Question

Want to see the full answer?

Answer 1

Question

Chapter 7, Problem 79P

Program Plan Intro

Aggregate Functions:

SQL has some built-in functions and they are called as aggregate functions.

SQL contains five built-in functions. They are:

SUM – This function is used to add values from the particular column.

Syntax: SELECT SUM(column_Name) FROM table_Name;

COUNT – This is used to count the number of rows for the particular column.

Syntax: SELECT COUNT(column_Name) FROM table_Name;

MAX – This function is used to get the maximum value from the column.

Syntax: SELECT MAX(column_Name) FROM table_Name;

MIN – This function is used to get the minimum value from the column.

Syntax: SELECT MIN(column_Name) FROM table_Name;

AVG – This function is used to get the average of all the values from the column.

Syntax: SELECT AVG(column_Name) FROM table_Name;

DISTINCT Keyword:

“DISTINCT” keyword is used to avoid redundant data (removing duplicate values) from a column. The syntax for “DISTINCT” keyword is as follows:

SELECT DISTINCT column_Name FROM table_Name;

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

15 points Save ARS Consider the following scenario in which host 10.0.0.1 is communicating with an external SMTP mail server at IP address 128.119.40.186. NAT translation table WAN side addr LAN side addr (c), 5051 (d), 3031 S: (e),5051 SMTP B D (f.(g) 10.0.0.4 server 138.76.29.7 128.119.40.186 (a) is the source IP address at A, and its value. S: (a),3031 D: (b), 25 10.0.0.1 A 10.0.0.2. 1. 138.76.29.7 10.0.0.3

6.3A-3. Multiple Access protocols (3). Consider the figure below, which shows the arrival of 6 messages for transmission at different multiple access wireless nodes at times t=0.1, 1.4, 1.8, 3.2, 3.3, 4.1. Each transmission requires exactly one time unit. 1 t=0.0 2 3 45 t=1.0 t-2.0 t-3.0 6 t=4.0 t-5.0 For the CSMA protocol (without collision detection), indicate which packets are successfully transmitted. You should assume that it takes .2 time units for a signal to propagate from one node to each of the other nodes. You can assume that if a packet experiences a collision or senses the channel busy, then that node will not attempt a retransmission of that packet until sometime after t=5. Hint: consider propagation times carefully here. (Note: You can find more examples of problems similar to this here B.] ☐ U ப 5 - 3 1 4 6 2

Just wanted to know, if you had a scene graph, how do you get multiple components from a specific scene node within a scene graph? Like if I wanted to get a component from wheel from the scene graph, does that require traversing still? Like if a physics component requires a transform component and these two component are part of the same scene node. How does the physics component knows how to get the scene object's transform it is attached to, this being in a scene graph?