A cantilever beam of rectangular cross section (width b = 25 mm. height h= 100 mm) is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a to the vertical (see figure). Two strain gages are placed at point C. which also is at the midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle B = 60 to the horizontal. The measured strains are e 125 x 10 and e, -375 x 10-, Determine the force P and the angle a, assuming the material is steel with E- 200 GPa and = 1/3.

A cantilever beam of rectangular cross section (width b = 25 mm. height h= 100 mm) is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a to the vertical (see figure). Two strain gages are placed at point C. which also is at the midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle B = 60 to the horizontal. The measured strains are e 125 x 10 and e, -375 x 10-, Determine the force P and the angle a, assuming the material is steel with E- 200 GPa and = 1/3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: the position of maximum displacement in the segment AB. Hint: remember that coordinate x₁ is…

A: Given data

Q: A flexible connection consisting of rubber pads(thickness t =9 mm) bonded to steel plates is shown…

A: Given Force P =16 kN Shear modulus for the rubber is G = 1250 kPa Thickness t =9 mm Find…

Q: A thin rectangular polymer plate PQRS of width b = 425 mm and height a = 144 mm is shown in the…

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:- Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: A circular post, a rectangular post, and a post of cruciform cross section are each compressed by…

A: Given: Diameter and the depth of rectangular and cruciform post=d Load acting at corner of the each…

Q: A bar with a circular cross section having twodifferent diameters d and 2d is shown in the…

A: When an elastic body is loaded it undergoes deformation i.e its dimensions change and when it is…

Q: A cantilever beam with a rectangular cross section (width b = 20 mm, height Ii = 175mm) is loaded by…

Q: A rectangular element as shown in the figure is used to represent a pure bending problem. Due to the…

Q: 2. The component shown always breaks at point C, which is just to the right of the contact point of…

A: The component always breaks at point C, which is just right of the contact point of the roller at B.…

Q: ENT 1 TITLE: TOTAL DESIGN ACTIVITY EXERCISE PRODUCT DESIGN SPECIFICATION (PDS) Due Date: 30th April…

A: Given Gran unloading system To find Counter questions by an engineer

Q: A beam subjected to a bending test has internal vertical shear force V=2000N. The cross-sectional…

Q: e) the value of the constant of integration C₂. Enter your answer in kNm3³ to 3 decimal places.

A: P = 3.9 kN a = 1.5 mb = 1.3 mFree body diagram,

Q: 2. For the dimensions provided below, what would be the expected strain at point A if the…

A: Length of the cantilever (a+b): a+b=8+2=10 inches.Point load (F) acting at a distance a from the…

Q: rod ABC is applied with axial loading as shown in Figure Q4(a). Using E = 200 GPa, determine (i) the…

A: Given:E=200 GPaP=36 KNd=16 mmD=20 mmLAB=600 mmLBC=900 mm

Q: A simply supported beam (i.e., with a pin support at point A and a roller support at point D) is…

Q: The figure shows a rectangular section beam with a distributed load of 3 KN/m. Decide: The maximum…

A: Consider a beam having Area Moment of Inertia I and Young's modulus E is subjected to bending moment…

Q: h) Strain energy for truss CE. Enter your answer in J to 2 decimal places.

Q: The two bars shown in the figure are used to support a load P. When unloaded, joint B has…

A: The dimension are

Q: Cross section of a beam is shown in Figure 3. If a shear force V=100 kN is applied to the beam, find…

Q: both cables have a diameter of 5 mm, find : The normal strain for both wires using both the small…

Q: (1) A cantilever steel beam with the triangular cross section is loaded with the concentrated force…

A: Given:To find:Stress state at point M.

Q: A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The…

Q: Consider the beam shown in sketch below, hinge supported at point A and roller supported at point D.…

A: Considering the cross-section of the beam The web is denoted as 1 and flange is denoted as 2

Q: Part A In this problem you will consider the balance of thermal energy radiated and absorbed by a…

A: Law states that the radiation energy emitted from the surface of a black body per unit time per unit…

Q: 13. A steel pipe of length L=150cm outside diameter d2 = 15 cm, and inside diameter d₁ =11cm is…

A: 6. Dilatation (e) : Dilatation e is the volumetric strain: e = 3ε e =3×0.00035 e =…

Q: Parvinbhai

A: Step 1: Step 2: Step 3: Step 4:

Q: 4.3-5 Determine the shear force V and bending moment M at a cross section located 16 ft from the…

A: Determine the shear force V and bending moment M at a cross section located 16 ft from the left-hand…

Q: 120 KN 100 mm H 400 mm B 22m 150 mm Find the shear stress at point H on the beam. The wall thickness…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 5.1 m long simply supported wood beam carries a uniformly distributed load of 11.3 kN/m, as shown in Figure A. The cross-sectional dimensions of the beam as shown in Figure B are b = 205 mm, d = 460 mm, yH = 77 mm, and yx = 162 mm. Section a-a is located at x = 1.3 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) If the allowable shear stress for the wood is 850 kPa, what is the largest distributed load w that can be supported by the beam? х В L Figure A
The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.20 in., -0.55 in.). Assume a = 9 ft, b = 6 ft, and h = 7 ft. Determine the normal strain in each bar. B P b h
Determine the normal strain AB and BC
4. The simply supported beam has a cross section and a loading as shown in the figure (a) Draw the shear and bending-moment diagrams for the beam (b) Determine the maximum absolute value of the shear force and bending moment. (c) Determine the maximum tensile and compressive stresses in the beam. A 30 kN/m 2 m C 60 kN D 2 m B T 1 150 mm 50 mm T
Determine the axial force, shear force, and bending moment at point J located on member AB of the landing gear of an airplane, as shown in the figure.All distances are in inches.
P=50 kN E=200GPa l=1.4 m Ø=16mm
Athin rectangular polymer plate PQRS of width b = 429 mm and height a = 140 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 1.6 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. a Y = y i b Q S a X urad
A surface condenser deals with 12000 kg of steam per hour. Air leakage into the condenser is found to be 4 kg/hr. The vacuum and temperature at the air pump suction are 700 mm of Hg and 36°C respectively. The barometric pressure is 760 mm Hg. Compute the volumetric capacity in m'/min of wet air pump.
A symmetrical framework consisting of threepin-connected bars is loaded by a force P (see figure).The angle between the inclined bars and the horizontalis α = 52°. The axial strain in the middle bar ismeasured as 0.036.Determine the tensile stress in the outer bars ifthey are constructed of a copper alloy having the followingstress-strain relationship:σ = 18,000ε/(1 + 300ε) 0 ≤ ε ≤ 0.03 (σ= ksi)
A 8 B 0 2 3 Calculate the shear force in kN at x=2,5 m in the beam in the figure. Note: The absolute magnitude of the force must be taken into account. C D E 0,25 2,75 3,25 4 kN/m 4 3 kN/m 4 KN 5 6 z (m)
0.19