The inlet pressure for given catalyst tower should be determined. Concept introduction: The pressure drop through the catalyst tower is calculated by the Ergun equation which is a combination of the Kozeny-Carman equation and Burke-Plummer equation. The Kozeny-Carman equation is applicable for the particles in a bed whose Reynold’s number is less than 1. It is given as, ΔP L = 150 V ¯ 0 μ(1-ε) 2 ϕ s 2 D p 2 ε 3 ....... ( 1 ) In the above formula, the notations used are, ΔP = Pressure drop through packed tubes L = Length of tube V ¯ 0 = Superficial velocity μ = Viscosity of fluid ε = Bed porosity D p = Pellet diameter ϕ s = Sphericity of particles The Burke Plummer equation is applicable for the particles in a bed whose Reynold’s number is more than 1000. It is given as, ΔP L = 1 .75 V ¯ 0 2 ρ(1-ε) ϕ s D p ε 3 ....... (2) ρ= Density of air The density of air can be given as, ρ = PM RT ....... ( 3 ) In the equation (3), notations used are, P is the pressure at which air enters M is the molecular weight of air R is the Universal Gas constant T is the temperature at which air enters Ergun equationis obtained by combining equation (1) and equation (2): ΔP L = 150 V ¯ 0 μ(1-ε) 2 ϕ s 2 D p 2 ε 3 + 1 .75 V ¯ 0 2 ρ(1-ε) ϕ s D p ε 3 ....... (4)

Question

Want to see the full answer?

Answer 1

Question

Chapter 7, Problem 7.2P

Interpretation Introduction

Interpretation:The inlet pressure for given catalyst tower should be determined.

Concept introduction: The pressure drop through the catalyst tower is calculated by the Ergun equation which is a combination of the Kozeny-Carman equation and Burke-Plummer equation.

The Kozeny-Carman equation is applicable for the particles in a bed whose Reynold’s number is less than 1. It is given as,

ΔPL=150V¯0μ(1-ε)2ϕs2Dp2ε3 ....... (1)

In the above formula, the notations used are,

ΔP = Pressure drop through packed tubesL = Length of tubeV¯0 = Superficial velocityμ = Viscosity of fluidε = Bed porosityDp = Pellet diameterϕs = Sphericity of particles

The Burke Plummer equation is applicable for the particles in a bed whose Reynold’s number is more than 1000. It is given as,

ΔPL=1.75V¯02ρ(1-ε)ϕsDpε3 ....... (2)

ρ= Density of air

The density of air can be given as,

ρ = PMRT ....... (3)

In the equation (3), notations used are,

P is the pressure at which air enters

M is the molecular weight of air

R is the Universal Gas constant

T is the temperature at which air enters

Ergun equationis obtained by combining equation (1) and equation (2):

ΔPL=150V¯0μ(1-ε)2ϕs2Dp2ε3 +1.75V¯02ρ(1-ε)ϕsDpε3 ....... (4)

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

Rotorences] Use the data below from an electron impact mass spectrum of a pure compound to deduce its structure. Draw your structure in the drawing window. Data selected from the NIST WebBook, https://webbook.nist.gov/chemistry/ m/z Relative intensity 73 1.0 72 25 57 8 43 100 29 17 • You do not have to consider stereochemistry. • You do not have to explicitly draw H atoms. • In cases where there is more than one answer, just draw one. 81 + ་་ CH4 { [ ? Previous Next

Only focus on H(3), which the answer is minus 1.26 KJ/mol. This also has the ideal gas of nitrogen gas N2. Two enthalpies need to be calculated for this. The first enthalpy is H = (specific volume) times (pressure difference). For the specific volume of nitrogen, how was 12.089 x10^(-5) m^3/mol obtained? I understand the second enthalpy for the heat capacity for nitrogen gas.

chemical engineering. The answer for H(3) is minus 1.26 KJ/mol. Demonstrate the reference state to the process state for nitrogen gas. I know that is an ideal gas law for the nitrogen gas. I know how to calculate the heat capacity for this.