Electrical Transformers and Rotating Machines
4th Edition
ISBN: 9781305494817
Author: Stephen L. Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 7, Problem 4RQ
A wye-connected load has a phase current of 25 A. How much current is flowing through the lines supplying the load?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Don't Use Chat GPT Will Upvote
Question 2 Calculate the amount of DC current required for the magnetic circuit given below to generate a
flux density of 1.0 T in the airgap. The details are
Number of turns, N = 400
The core is made up of steel, the B-H characteristic has been given below
The magnetic core length, le = 500 mm
The airgap length, Ig = 2 mm
The cross-sectional area of the core, Ag = 100 mm²
Neglect leakage and fringing.
Core
Cross-sectional
i(1)
area
as
Air gap
Magnetic path
length
Figure 1
2.0
1.8
B-H Curves for Various Metals
Steel
1.6
1.4
Magnetic
Saturation
1.2
1.0
0.8
Iron
근 0.4
Air
0.2
1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
Magnetic Field Strength - H (A/m)
Figure 2
Flux Density - B (T)
A balanced star-connected load of (8 + j6) Q per phase is connected to a Balanced 3- phase 400-V supply. Find the line current, power factor, power
Chapter 7 Solutions
Electrical Transformers and Rotating Machines
Ch. 7 - Prob. 1RQCh. 7 - Prob. 2RQCh. 7 - A wye-connected load has a voltage of 480 V...Ch. 7 - A wye-connected load has a phase current of 25 A....Ch. 7 - Prob. 5RQCh. 7 - A delta connection has 30 A of current flowing...Ch. 7 - A three-phase load has a phase voltage of 240 V...Ch. 7 - If the load in question 7 is connected in a wye,...Ch. 7 - An alternator with a line voltage of 2400 V...Ch. 7 - Prob. 10RQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- If a single-phase load is connected across the two line conductors and neutral of the transformer in question #2, and one line has a current of 80 amps and the other line has a current of 68 amps, how much current is flowing in the neutral conductor?arrow_forwardA current transformer has a ratio of 600:5. If three loops of wire are wound through the transformer core, how much primary current is required to produce 5 amperes of current in the secondary winding?arrow_forwardA wye-connected load has a voltage of 480 V applied to it. What is the voltage dropped across each phase?arrow_forward
- If the secondary of the transformer in question 5 supplies a current of 9.6 amperes to a load, what is the primary current? (Disregard excitation current.)arrow_forwardA delta connection has 30 A of current flowing through each phase winding. How much current is flowing through each of the lines supplying power to the load?arrow_forwardName three factors that determine the amount of induced voltage.arrow_forward
- Assume that a primary current of 75 amperes flows through the windings of the transformer in question 4. How much current will flow in the secondary winding?arrow_forwardA current transformer has 4 turns of wire in its primary winding. How many turns of wire are needed in the secondary winding to produce a current of 2 amperes when a current of 60 amperes flows in the primary winding?arrow_forwardA 480-volt three-phase load is rated at 34.5 kVA. It is to be supplied with variable three-phase voltage. Because the load is continuous, the transformers ratings are to be increased by 1.25% of the rated load. Three variable autotransformers are used to supply this load. Refer to Table 4-2 and determine the standard size of each transformer that should be used to make this connection.arrow_forward
- A load impedance of 52 Ω is connected to the secondary winding of the transformer in question 3. How much current will flow in the secondary?arrow_forwardA large motor has a full load current rating of 425 amperes. Current transformers with a ratio of 600:5 are used to reduce the current to the overload heaters. What should be the full load current rating of the overload heaters?arrow_forwardexplain what happened here.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage LearningUnderstanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license