Concept explainers
(III) A 3.0-m-long steel chain is stretched out along the top level of a horizontal scaffold at a construction site, in such a way that 2.0 m of the chain remains on the top level and 1.0 m hangs vertically, Fig. 7–26. At this point, the force on the hanging segment is sufficient to pull the entire chain over the edge. Once the chain is moving, the kinetic friction is so small that it can be neglected. How much work is performed on the chain by the force of gravity as the chain falls from the point where 2.0 m remains on the scaffold to the point where the entire chain has left the scaffold? (Assume that the chain has a linear weight density of 18 N/m.)
FIGURE 7-26
Problem 49.
Let y represent the length of chain hanging over the table, and let λ represent the weight per unit length of the chain. Then the force of gravity (weight) of the hanging chain is FG = λy. As the next small length of chain dy comes over the table edge, gravity does an infinitesimal amount of work on the hanging chain given by the force tunes the distance. FGdy = λydy. To find the total amount of work that gravity does on the chain, integrate that work expression, with the limits of integration representing the amount of chain hanging over the table.
Want to see the full answer?
Check out a sample textbook solutionChapter 7 Solutions
Physics for Scientists and Engineers with Modern Physics
Additional Science Textbook Solutions
Physics: Principles with Applications
College Physics (10th Edition)
Applied Physics (11th Edition)
An Introduction to Thermal Physics
Tutorials in Introductory Physics
Life in the Universe (4th Edition)
- 14-89. When the 6-kg box reaches point A it has a speed of vA = 2 m/s. Determine the angle 0 at which it leaves the smooth circular ramp and the distance s to where it falls into the cart. Neglect friction. VA = 2 m/s 20° B 1.2 marrow_forward11.)A 25 kg block is to be pushed down a 7.0 degree incline and should have a speed of 18m/s at the end of 72 meter. Coefficient of kinetic friction is 0.10. How much force is needed to push it down?arrow_forwardA 80.0-kg person jumps onto the floor from a height of 5.00 m. If he lands stiffly (with his knee joints compressing by 0.500 cm), calculate the force on the knee joints.arrow_forward
- (b) Repeat the calculation if the applied force is exerted at an angle of 0 = 30.0° with the horizontal. = 441.15 W fric = 66.7 net HINTS: GETTING STARTED | 'M STUCK! EXERCISE (a) The Eskimo pushes the same 50.0-kg sled over level ground with a force of 2.15 x 104 N exerted horizontally, moving it a distance of 6.75 m over new terrain. If the net work done on the sled is 2.75 x 10 J find the coefficient of kinetic friction. 0.355 (b) Repeat the exercise with the same data, finding the coefficient of kinetic friction, but assume the applied force is upwards at a 35.0° angle with the horizontal. 0.399 Your responst is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error. Need Help? Read It O Show My Work (Optional)arrow_forward(a) Calculate the force (in N) needed to bring a 950 kg car to rest from a speed of 90.0 km/h in a distance of 110 m (a fairly typical distance for a non-panic stop). (b) Suppose instead the car hlts a concrete abutment at full speed and is brought to a stop in 2.00 m. Calculate the force exerted on the car and compare it with the force found in part (a) force In (b) force in (a)arrow_forward6) Z. A thin non-condu cting rod of ma ss m and length L = 60cm, slides frictionl essly at a constant speed V = 0.5 m/s along the rails placed on the surface and at the edges of an inclined plane with the effect of an external force. The rails at the edges of the inclined plane are connected with each other via the rail at the bottom edge of the plane, so the rod and rails forms a rectangular closed loop as seen in the figure. The plane of the rails makes an angle 0 = 55° with the horizontal plane (xz plane). Before sliding, the rod stays at the di stan ce S = 4m measured from the bottom edge of the inclined plane. The inclined plane and the rod are under the effect of a uniform magnetic field given by B = 0.40î + 3ĵ + 0.8k(T). After the rod starts to slide, what will be the magnetic flux passing through the surface formed by the rod, the rails at the edges, and the rail at the bottom edge of the inclined plane at t=4s? A) 1.50 Wb B) 7.53 Wb C) 0.083 Wb D) 0.147 Wb E) 1.67 Wbarrow_forward
- (2) A 30 B 30 Black: weight weight = W₁A = TBD Rod: [weight = W = 46 N length = L = will cancel out friction: μg = 0.20 Block A is positioned on a 30° slope, and is connected by a card to end of the top end of Rod. Bc, as shown. The coeffienet of static friction at all three sites (A, B, and C) is μg = 0.20. Assuming that the pulley is frictionless, find the smallest value of WA that is consistent with equilibrium.arrow_forward(a) Calculate the force needed to bring a 800 kg car to rest from a speed of 85.0 km/h in a distance of 130 m (a fairly typical distance for a nonpanic stop). ............N(b) Suppose instead the car hits a concrete abutment at full speed and is brought to a stop in 2.00 m. Calculate the force exerted on the car and compare it with the force found in part (a), i.e. find the ratio of the force in part(b) to the force in part(a)..............(force in part (b) / force in part (a))arrow_forwardHang the spring balance on the right side of the lever at the 10 mark and pull the spring balance so that the lever comes into a horizontal position. (ii) Read the indicated value of force meter and record it in Table 1 on the Results page. (iv) Move the load successively to the 8, 6, 4 and 2 marks on the left side and measure the force for each position and record it in Table 1 on the Results page. Question – 1: Using the mass m, calculate the load (force) and record it above the table – 1. Question – 2: From the distance between the marks used (2 cm each), calculate the length of the load arm di and the force arm di in cm and add these values to the result tables. Question – 3: Calculate the products L × di und F x dh and record these values in the result tables. Mass = 100 g, Load (L) = 980 N TABLE - 1 Objects di (cm) L x di (Ncm) F (N) d2 (cm) Fx d2 (Ncm) Left Right side side Load Force 10 10 1.0 8 10 0.78 6 10 0.58 4 10 0.40 2 10 0.20arrow_forward
- Considering all Surfaces friction is 0.3, Determine the Maximum Value of force P without causing the 60kg block to move.arrow_forward(a) Tony Hawco (m362 kg), a Newfoundland based skater decides to have his first ride on the new halfpipe at Bannerman Park. We will use the lowest point in the halfpipe as our reference point h=0. Vo=2.00 m/s R=3.00 m V,=7.00 m/s h=0 B. A.arrow_forward(a) Calculate the force needed to bring a 1050 kg car to rest from a speed of 80.0 km/h in a distance of 120 m (a fairly typical distance for a nonpanic stop). N(b) Suppose instead the car hits a concrete abutment at full speed and is brought to a stop in 2.00 m. Calculate the force exerted on the car and compare it with the force found in part (a), i.e. find the ratio of the force in part(b) to the force in part(a). (force in part (b) / force in part (a))arrow_forward
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningUniversity Physics (14th Edition)PhysicsISBN:9780133969290Author:Hugh D. Young, Roger A. FreedmanPublisher:PEARSONIntroduction To Quantum MechanicsPhysicsISBN:9781107189638Author:Griffiths, David J., Schroeter, Darrell F.Publisher:Cambridge University Press
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningLecture- Tutorials for Introductory AstronomyPhysicsISBN:9780321820464Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina BrissendenPublisher:Addison-WesleyCollege Physics: A Strategic Approach (4th Editio...PhysicsISBN:9780134609034Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart FieldPublisher:PEARSON