Explanation Given information: The magnitude of the largest resultant force acting at point A is R A = 2 kN . Assumption: Consider the state of member as tension, where the force is pulling the member and as compression, where the force is pushing the member. Consider the force indicating the right side as positive and the left side as negative in the horizontal components of forces. Consider the force indicating upward as positive and downward as negative in the vertical components of forces. Consider the clockwise moment as negative and the anti-clockwise moment as positive, wherever applicable. Use the equation of equilibrium, wherever applicable. Entire structure: Show the free-body diagram of the entire structure as in Figure 1. Using Figure 1, Moment about the point A : Determine the tension in the cable T in terms of force P by taking the moment about the point A . ∑ M A = 0 T ( 0.6 ) − P ( 1.5 ) = 0 (I) Along the vertical direction: Determine the vertical reaction at point A by resolving the vertical component of forces. ∑ F y = 0 A y − P = 0 (II) Along the horizontal direction: Determine the horizontal reaction at point A by resolving the horizontal component of forces. ∑ F x = 0 A x − T = 0 (III) Conclusion: Solve Equation (I). T ( 0.6 ) − P ( 1.5 ) = 0 0

13th Edition

ISBN: 9780132915540

Author: Russell C. Hibbeler

Publisher: Prentice Hall

See similar textbooks

Question

Chapter 6.6, Problem 68P

To determine

The greatest force P that can be applied to the frame.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 6.6, Problem 67P

Chapter 6.6, Problem 69P

Students have asked these similar questions

w1 Three distributed loads act on a beam as shown. The load between A and B increases linearly from 0 to a maximum intensity of w₁ = 12.8 lb/ft at point B. The load then varies linearly with a different slope to an intensity of w₂ = 17.1 lb/ft at C. The load intensity in section CD of the beam is constant at w3 10.2 lb/ft. For each load region, determine the resultant force and the location of its line of action (distance to the right of A for all cases). cc 10 BY NC SA 2016 Eric Davishahl = WI W2 W3 -b- C Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 4.50 ft b 5.85 ft с 4.28 ft The resultant load in region AB is FR₁ = lb and acts ft to the right of A. The resultant load in region BC is FR2 lb and acts = ft to the right of A. The resultant load in region CD is FR3 = lb and acts ft to the right of A.

The T-shaped structure is embedded in a concrete wall at A and subjected to the force F₁ and the force-couple system F2 1650 N and M = 1,800 N-m at the locations shown. Neglect the weight of the structure in your calculations for this problem. = a.) Compute the allowable range of magnitudes for F₁ in the direction shown if the connection at A will fail when subjected to a resultant moment with a magnitude of 920 N- m or higher. b.) Focusing on the forces and igonoring given M for now. Using the value for F1, min that you calculated in (a), replace the two forces F₁ and F2 with a single force that has equivalent effect on the structure. Specify the equivalent →> force Feq in Cartesian components and indicate the horizontal distance from point A to its line of action (note this line of action may not intersect the structure). c.) Now, model the entire force system (F1,min, F2, and M) as a single force and couple acting at the junction of the horizontal and vertical sections of the…

The heated rod from Problem 3 is subject to a volumetric heating h(x) = h0 x L in units of [Wm−3], as shown in the figure below. Under the heat supply the temperature of the rod changes along x with the temperature function T (x). The temperature T (x) is governed by the d following equations: − dx (q(x)) + h(x) = 0 PDE q(x) =−k dT dx Fourier’s law of heat conduction (4) where q(x) is the heat flux through the rod and k is the (constant) thermal conductivity. Both ends of the bar are in contact with a heat reservoir at zero temperature. Determine: 1. Appropriate BCs for this physical problem. 2. The temperature function T (x). 3. The heat flux function q(x). Side Note: Please see that both ends of bar are in contact with a heat reservoir at zero temperature so the boundary condition at the right cannot be du/dx=0 because its not thermally insulated. Thank you

Chapter 6 Solutions

Engineering Mechanics: Statics

Ch. 6.3 - State if the members are in tension or...Ch. 6.3 - State if the members are in tension or...Ch. 6.3 - Prob. 3FP Ch. 6.3 - Determine the greatest load P that can be applied...Ch. 6.3 - Identify the zero-force members in the truss....Ch. 6.3 - State if the members are in tension or...Ch. 6.3 - Prob. 1P Ch. 6.3 - Prob. 2P Ch. 6.3 - Determine the force in each member of the truss,...Ch. 6.3 - Determine the force in each member of the truss,...

Knowledge Booster