Concept explainers
The solution of Laplace' equation.
Answer to Problem 6.43P
The potential field
Explanation of Solution
Calculation:
The Poisson's equation (generalization of Laplace equation) is defined for
The Poisson's equation is written as
Here,
Simplify equation (1) as,
Integrate equation (2) with respect to spherical coordinate
Substitute
Simplified the equation (4) as,
The Laplace's equation is defined for
The Laplace's equation is written as
Integrate the equation (5) with respect to spherical coordinate
Equation (6) is multiplied with
If equation (6) and equation (7) is equal, then it is written as
Simplified the equation (8) as,
Substitute
At boundary condition
Substitute
Simplify equation (12) as
Integrate the equation (3) with respect to
Substitute
Simplify equation (14) as
Integrate the equation (10) with respect to
Substitute
Equation (16) is simplified as
Substitute
Substitute
If equation (17) and equation (18) is equal, then it is written as
Substitute
Substitute
Substitute
The value of potential difference
Substitute
Substitute
Conclusion:
Therefore, the potential field
Want to see more full solutions like this?
Chapter 6 Solutions
Engineering Electromagnetics
- An evening meal is being prepared in a home kitchen containing an electric oven and a microwave oven. The cost for electricity in the home's neighborhood is $0.15 per kilowatt hour. The microwave oven is specified as a 1000 watt unit, while the oven requires 240 volts and uses a current of 30 amperes to cook at 350 degrees Fahrenheit. A frozen meal can be cooked in the microwave oven set on full power in 10 minutes. The same frozen meal cooked in the electric oven set for 350 degrees F takes 40 minutes. (a) How much energy does it take to cook the frozen meal in the microwave at full power and how much does it cost? (b) How much energy does it take to cook the frozen meal in the electric oven at 350 degrees Fahrenheit and how much does it cost?arrow_forwardDon't use ai to answer I will report you answerarrow_forwardAn electrical substation had a sudden discharge arc event lasting 0.005 seconds. The event produced 768,000 volts that conducted 500 amperes to a nearby grounded metal strap and opened a 500 ampere protective breaker. (a) How much power was produced by the electrical discharge? (b) How much energy was in the discharge? (c) How long could a 75 watt light bulb stay lit, if all the energy in the arc was used to operate it?arrow_forward
- I need help with this problem and an explanation of the solution for the image described below. (Introduction to Signals and Systems)arrow_forwardFind Rth at open terminals using a 1V test source.arrow_forwardI need help with this problem and an explanation of the solution for the image described below. (Introduction to Signals and Systems)arrow_forward
- How many atoms are there in a simple cubic unit cell? in a bcc unit cell? in a fcc unit cell? in the unit cell characterizing the diamond lattice?arrow_forwardConsider the homogeneous RLC circuit (no voltage source) shown in the diagram below. Before the switch is closed, the capacitor has an initial charge go and the circuit has an initial current go- R 9(1) i(t)↓ After the switches closes, current flows through the circuit and the capacitor begins to discharge. The equation that describes the total voltage in the loop comes from Kirchoff's voltage law: L di(t) + Ri(t)+(0) = 0, (1) where i(t) and q(t) are the current and capacitor charge as a function of time, L is the inductance, R is the resistance, and C is the capacitance. Using the fact that the current equals the rate of change of the capacitor charge, and dividing by L, we can write the following homogeneous (no input source) differential equation for the charge on the capacitor: 4(1) +29(1)+w79(1)=0, ཀྱི where a= R 2L and The solution to this second order linear differential equation can be written as: 9(1) =Aent - Beat, where (3) (4) (5) A= (81+20)90 +90 (82+20)90 +90 and B= (6)…arrow_forwardConsider the homogeneous RLC circuit (no voltage source) shown in the diagram below. Before the switch is closed, the capacitor has an initial charge go and the circuit has an initial current go. R w i(t) q(t) C н After the switches closes, current flows through the circuit and the capacitor begins to discharge. The equation that describes the total voltage in the loop comes from Kirchoff's voltage law: di(t) L + Ri(t) + (t) = 0, dt (1) where i(t) and q(t) are the current and capacitor charge as a function of time, L is the inductance, R is the resistance, and C is the capacitance. Using the fact that the current equals the rate of change of the capacitor charge, and dividing by L, we can write the following homogeneous (no input source) differential equation for the charge on the capacitor: ä(t)+2ag(t)+wg(t) = 0, (2) where R a 2L and w₁ = C LC The solution to this second order linear differential equation can be written as: where 81= q(t) = Ae³¹- Bel 82 = (3) (4) (5)arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,