Explanation Take all vectors along the x axis and y axis as positive. The Diagram of component of force F along A B is shown in figure1. From the figure 1, relation between force and distance given. ( F A B ) x 0.65 in . = ( F A B ) y 0.55 in (I) The free body diagram of the blade A C E . From figure 2, write the expression for the moment at C . ∑ M C = ∑ F × D ⊥ (II) Here, ∑ M C is the net moment at C , F is the force, and D ⊥ is the perpendicular distance between the C and the point where force is experienced. Above equation implies that net moment at any point is the sum of product of each force acting on the system and perpendicular distance of the force and the point. Thus, the expression of net clockwise moment M C at point C . ∑ M C = 0 (III) Here, ∑ M C is the sum of all moment of force at C . From the figure2, write the equilibrium expression for the total anticlockwise moment acting at C . ( 300 lb ) ( 1.6 in . ) − ( F A B ) x ( 0.5 in . ) − ( F A B ) y ( 1.4 in . ) = 0 (IV) Here, ( F A B ) x is the component of force along A B and ( F A B ) y is the component of force along A B . The free body diagram of the blade lower handle is shown in figure 3. From figure 3, write the expression for the moment at D . ∑ M D = ∑ F × D ⊥ (III) Here, ∑ M D is the net moment at d , F is the force, and D ⊥ is the perpendicular distance between the D and the point where force is experienced. Above equation implies that net moment at any point is the sum of product of each force acting on the system and perpendicular distance of the force and the point. Thus, the expression of net clockwise moment M D at point D . ∑ M D = 0 Here, ∑ M D is the sum of all moment of force at D . From the figure3, write the equilibrium expression for the total anticlockwise moment acting at D . ( F A B ) y ( 0

VEC MECH 180-DAT EBOOK ACCESS(STAT+DYNA)

12th Edition

ISBN: 9781260916942

Author: BEER

Publisher: MCG

See similar textbooks

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Videos

Question

Chapter 6, Problem 6.175RP

To determine

The tension in the fusible link DE and the force exerted on member BCE at B.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 6, Problem 6.174RP

Chapter 7.1, Problem 7.1P

Students have asked these similar questions

ed While tapping a hole, a machinist applies the horizontal forces shown, P= 3.4 lb and Q=3.15 lb, to the handle of the tap wrench. Show that these forces are equivalent to a single force, and specify, if possible, the point of application of the single force on the handle. 25 in The single force is applied on an extension of handle BD at a distance of 78.24in. to the right of B.

Please no hand writing solution

25 mm 60 mm 85 mm D 75 mm 6.136 The tongs shown are used to apply a total upward force of 45 ky on a pipe cap. Determine the forces exerted at D and F on tong ADF. E F 90 mm Fig. P6.136

Chapter 6 Solutions

VEC MECH 180-DAT EBOOK ACCESS(STAT+DYNA)

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The tension in the fusible link D E and the force exerted on member B C E at B .

Solution Summary: The author illustrates how the tension in the fusible link DE and the force exerted on member BCE are expressed.

Concept explainers

Videos

The tension in the fusible link DE and the force exerted on member BCE at B.

Want to see the full answer?

Chapter 6 Solutions