To determine The power produced by the stream. Explanation Given: The diameter of the nozzle ( d ) is 50 mm . The cart moves to the right with a constant velocity V cs is 2 m / s The discharge from the nozzle ( Q ) is 0.04 m 3 / s . Calculations: Consider the flow as steady and the fluid can be taken as ideal. Figure 1 shows the free body diagram of the water stream striking. Consider the control volume as a portion of water striking the cart. Calculate the velocity V A at point A using the formula; V A = Q A A = Q ( π r 2 ) V A = 0.04 π ( 0.025 ) 2 = 20.37 m / s Here, Q is the flow rate of water and r is the radius of nozzle. Determine the relative velocity V A / c s of control surface at point A using the formula; V A / c s = V A − V c s V A / c s = 20.37 − 2 = 18.37 m/s Here, V c s is the velocity of cart. The relative velocity at point A , B , and C is equal to 18.37 m/s . V B / c s = V C / c s = V A / c s = 18.37 m / s Determine the relative flow Q A / c s at point A using the formula; Q A / c s = V A / c s A A = V A / c s ( π r 2 ) Q A / c s = 18.37 [ π ( 0.025 ) 2 ] = 0.03607 m 3 / s Determine the relative flow rate at point B using the formula; Q B / c s = 3 4 ( Q A / c s ) Q B / c s = 3 4 ( Q A / c s ) = 0.75 × ( 0.03607 ) = 0.02705 m 3 / s Determine the relative flow rate at point C using the formula; Q C / c s = 1 4 ( Q A / c s ) Q C / c s = 1 4 ( Q A / c s ) = 0.25 × ( 0.03607 ) = 0.009018 m 3 / s Express the linear momentum Equation as follows; ∑ F = ∂ ∂ t ∫ c v V ρ d V + ∫ c s V ρ V ⋅ d A Here, V is the velocity, ρ is the density of water, d V is the differential volume, and d A is the differential area

2nd Edition

ISBN: 9780134626055

Author: HIBBELER

Publisher: PEARSON CUSTOM PUB.(CONSIGNMENT)

See similar textbooks

Videos

Question

Chapter 6, Problem 45P

To determine

The power produced by the stream.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 6, Problem 44P

Chapter 6, Problem 46P

Students have asked these similar questions

The heated rod from Problem 3 is subject to a volumetric heating h(x) = h0 x L in units of [Wm−3], as shown in the figure below. Under the heat supply the temperature of the rod changes along x with the temperature function T (x). The temperature T (x) is governed by the d following equations: − dx (q(x)) + h(x) = 0 PDE q(x) =−k dT dx Fourier’s law of heat conduction (4) where q(x) is the heat flux through the rod and k is the (constant) thermal conductivity. Both ends of the bar are in contact with a heat reservoir at zero temperature. Determine: 1. Appropriate BCs for this physical problem. 2. The temperature function T (x). 3. The heat flux function q(x). Side Note: Please see that both ends of bar are in contact with a heat reservoir at zero temperature so the boundary condition at the right cannot be du/dx=0 because its not thermally insulated. Thank you

The elastic bar from Problem 1 spins with angular velocity ω about an axis, as shown in the figure below. The radial acceleration at a generic point x along the bar is a(x) = ω2x. Under this radial acceleration, the bar stretches along x with displacement function u(x). The displacement d u(x) is governed by the following equations: dx (σ(x)) + ρa(x) = 0 PDE σ(x) = E du dx Hooke’s law (2) where σ(x) is the axial stress in the rod, ρ is the mass density, and E is the (constant) Young’s modulus. The bar is pinned on the rotation axis at x = 0 and it is also pinned at x = L. Determine: 1. Appropriate BCs for this physical problem. 2. The displacement function u(x). 3. The stress function σ(x). SIDE QUESTION: I saw a tutor solve it before but I didn't understand why the tutor did not divide E under the second term (c1x) before finding u(x). The tutor only divided E under first term. please explain and thank you

calculate the total power required to go 80 mph in a VW Type 2 Samba Bus weighing 2310 lbs. with a Cd of 0.35 and a frontal area of 30ft^2. Consider the coefficient of rolling resistance to be 0.018. What is the increase in power required to go the same speed if the weight is increased by 2205 pounds (the rated carrying capacity of the vehicle). If the rated power for the vehicle is 49 bhp, will the van be able to reach 80 mph at full carrying capacity?

Chapter 6 Solutions

EBK FLUID MECHANICS

Ch. 6 - Prob. 1FP Ch. 6 - The shield of negligible weight is held at an...Ch. 6 - Prob. 3FP Ch. 6 - Crude oil flows into the open air at the same rate...Ch. 6 - The table fan develops a slipstream that has a...Ch. 6 - Prob. 6FP Ch. 6 - Determine the linear momentum of a mass of fluid...Ch. 6 - Prob. 2P Ch. 6 - A volumetric discharge of 1.25 m3/s passes out the...Ch. 6 - Water flows with a velocity of 6 m/s through the...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.