Concept explainers
In many textbook problems, we ignore certain complications such as friction and drag. The problems contain key words that indicate such a simplification is being used. For example, if a surface is described as “slippery,” it means that we can ignore friction. Look at the previous chapters’ problem sets. Find five uses of these key words and explain how to interpret each case.
The simplification of problems by using keywords.
Answer to Problem 1PQ
Some keywords that simplify the problem are constant speed, straight line motion, parabolic trajectory, etc.
Explanation of Solution
In most cases, friction and air drag are neglected unless and until mentioned. When it is given “constant speed along a straight line path”, it implies that the acceleration and the net force on the moving body is zero. Also if the motion is along a straight line, the distance and displacement are the same and hence the speed and velocity are same.
When mentioned “follows a parabolic trajectory”, it means that the object undergoes projectile motion with negligible air resistance. An object “subjected to constant acceleration suddenly” would mean that the change in acceleration can be considered instantaneous.
While blocks on ice are considered, frictional force is ignored because they are negligibly small.
Want to see more full solutions like this?
Chapter 6 Solutions
Physics for Scientists and Engineers: Foundations and Connections
- Please help. How would one go about finding the value for n from a slope in the following equation. In the previous step of an experiment, we determined the drag coefficient with n=2. So in this next step, all values are known except for n.arrow_forwardA cube of mass m = 61 kg slides along a horizontal surface. The coefficient of friction between the cube and the surface is μk = 0.41. The cube has an initial speed of vo = 18 m/s in the positive x-direction as shown. a. Write an expression for the x-component of the frictional force the cube experiences, Ff, in terms of the given variables and variables available in the palette. b. What is the magnitude of the frictional force in N? c. How far will the cube travel, in meters, before coming to rest?arrow_forwardIn the Wall of Death carnival attraction, stunt motorcyclists ride around the inside of a large, 12-m-diameter wooden cylinder that has vertical walls as shown in (Figure 1). The coefficient of static friction between the riders' tires and the wall is 0.90. Figure 1 of 1 Part A What is the minimum speed at which the motorcyclists can ride without slipping down the wall? Express your answer with the appropriate units. V = Submit µÅ Value Provide Feedback Request Answer Units ? Next >arrow_forward
- Draw a free-body diagram for block A. The figure shows a block (mass ma) on a smooth horizontal surface, connected by a thin cord that passes over a pulley to a second block (mass mB), which hangs vertically. Ignore friction and the masses of the pulley and cord. (Figure 1) Draw the vectors starting at the black dots. The location and orientation of the vectors will be graded. The exact length of your vectors will not be graded. No elements selected Select the elements from the list and add them to the canvas setting the appropriate attributes. Submit Request Answer Figure 1 of 1 Part B Draw a free-body diagram for block B. MA Draw the vectors starting at the black dots. The location and orientation of the vectors will be graded. The exact length of your vectors will not be graded. MB No elements selectedarrow_forwardTwo masses M1 (3kg) and M2 (1kg) are set up as shown in the attached diagram. The coefficient of kinetic friction between M1 and the horizontal surface is uk = 0.12, but there is negligible friction between M2 and the ramp sloped at 30 degrees to the horizontal. The pulley is ideal, and the string is massless. Assume g=10 N/kg. a. Write a force equation for both masses, along with a fully labeled free-body diagram for each. b. Using the two equations, solve for and calculate the acceleration of mass M2. c. Assuming the masses started from rest, and the ramp and string are long enough, what is the magnitude of the momentum of the whole system after M2 has moved 0.5m downwards along the plane of the ramp?arrow_forwardHow do the values of µs compare to the values of µk? (Of course, you can only compare them for the same pairs of materials.) Is the relationship between µs and µk what you expected? Explain. What are three reasons why friction is needed? Does the coefficient of friction change with mass? How can we reduce friction? What would happen if there was no friction? Does frictional force depend on mass? What are 3 factors that affect friction? Is friction affected by surface area? Can humans live without friction? Why is the coefficient of friction less than 1? Explain.arrow_forward
- A crate of mass m = 1.27 kg is on a frictionless incline that makes an angle of θ = 29.3 degrees with horizontal. A force of magnitude P = 9.45 N is applied to the crate in a direction parallel and up the incline, as shown. a. Write an expression for the acceleration ax of the crate, where positive x is up the incline. Your answer should be in terms of m, P, θ, and g (9.80 m/s2). b. What is the acceleration of the crate in m/s2 in the x direction defined in part (a)? c. What is the direction of the net force on the crate? d. What is the direction of the velocity of the crate?arrow_forwardA 150-g baseball is dropped from a tree 15.0 m above the ground. a.)With what speed would it hit the ground if air resistance could be ignored? Express your answer to three significant figures and include the appropriate units. b.)If it actually hits the ground with a speed of 8.00 m/s, what is the magnitude of the average force of air resistance exerted on it? Express your answer to three significant figures and include the appropriate units.arrow_forwardIn a laboratory experiment on friction, a 139-N block resting on a rough horizontal table is pulled by a horizontal wire. The pull gradually increases until the block begins to move and continues to increase thereafter. The figure (Figure 1) shows a graph of the friction force on this block as a function of the pull. Part C What would the graph look like if a 139 N brick were placed on the block, and what would be the coefficients of friction be in that case? Drag the terms on the left to the appropriate blanks on the right to complete the sentences. Figure 1 of 1 double The values of the maximum static friction and the same kinetic friction would be relative to those for the lone block. be a inclined line f(N) only 75.0 The graph would half 50.0 The coefficients of friction would be have the same 25.0 relative to those for the lone shape block. P (N) be a horizontal 25.0 50.0 75.0 100.0 125.0 150.0 onlyarrow_forward
- A student wants to determine the coefficient of static friction between a long, flat wood board and a small wood block. (a) Describe an experiment for determining the coefficient of static friction between the wood board and the wood block. Assume equipment usually found in a school physics laboratory is available. i. Draw a diagram of the experimental setup of the board and block. In your diagram, indicate each quantity that would be measured and draw or state what equipment would be used to measure each quantity. ii. Describe the overall procedure to be used, including any steps necessary to reduce experimental uncertainty. Give enough detail so that another student could replicate the experiment. (b) Derive an equation for the coefficient of static friction in terms of quantities measured in the procedure from part (a). A physics class consisting of six lab groups wants to test the hypothesis that the coefficient of static friction between the board and the block equals the…arrow_forwardA brick of mass m = 78 kg slides along a horizontal surface. The coefficient of friction between the brick and the surface is μk = 0.23. The brick has an initial speed of vo = 29 m/s in the positive x-direction as shown. a.) Write an expression for the x-component of the frictional force the brick experiences, Ff, in terms of the given variables and variables available in the palette. b.) What is the magnitude of the frictional force in N? c.) How far will the brick travel, in meters, before coming to rest?arrow_forwardInstruction: Provide complete solutions with the derivation of formulas (integrals and derivatives). Use two decimal places for final answers only. The final answers shown below are incomplete. (Dynamics of Rigid Bodies) A machine is used to cause an object to move along a curved path with a radius of 1 ft. The object has a mass of 5 lbm and is subjected to a force of (F = 2t + 1)lbf, where t is in seconds. Find the change in momentum of the object after 3 seconds if it was initially traveling at 2 ft/s. lbm-ft² Answers: 386.09 Sarrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning