Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 6, Problem 12RQ
Which of the following statements about manifold gauge sets is not true?
- An adapter is required for using R-12 gauges on an R-134a system.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A(n)
is used to diagnose gauge
problems by substituting precise
resistances in the gauge circuit and
comparing the gauge reading to the
specifications.
Select one:
a. Additive substitution box
b. Resistance substitution box
c. Gauge reading box
d. Oil pressure sensor
Testing oil pressure sensors usually
involves substituting the specified
in place of the sensor and
observing the reaction of the oil pressure
gauge.
Select one:
a. Pressure
b. Voltage
c. Resistance
d. None of the above
Name and sketch the three types of plug gauges
Chapter 6 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 6 - Explain why testlights are not recommended for...Ch. 6 - True or False? A compression gauge will show the...Ch. 6 - Name the two basic types of compression gauges.Ch. 6 - What tool is used to test engine manifold vacuum.Ch. 6 - Prob. 5RQCh. 6 - Technician A says that a brake drum micrometer has...Ch. 6 - Technician A says that a pyrometer measures...Ch. 6 - True or False? A lab scope is a visual voltmeter...Ch. 6 - Prob. 9RQCh. 6 - Technician A uses a digital volt/ohmmeter to test...
Ch. 6 - Technician A says that a charging station removes...Ch. 6 - Which of the following statements about manifold...Ch. 6 - True or False? A brake shoe adjusting gauge is an...Ch. 6 - When conducting an oil pressure test: Technician A...Ch. 6 - Which of the following conditions can be revealed...Ch. 6 - Technician A uses a high-impedance testlight on...Ch. 6 - Technician A says that a sulfated and plugged fuel...Ch. 6 - The tests conducted by a scan tool can also be...Ch. 6 - When using a fuel injector pulse tester....Ch. 6 - To measure engine cranking current, a DNIM...Ch. 6 - While discussing a clutch alignment tool....Ch. 6 - True or False? The angle of the drive shaft at the...Ch. 6 - Technician A says that ball joints may be pressed...Ch. 6 - Which of the following is not a suitable way to...Ch. 6 - Prob. 25RQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following statements about oil gauge circuits is not true? A switch can be used A thermistor can be used. A piezoresistive sensor can be used d An oil pressure gauge may not show actual oil pressure.arrow_forwardList the components usually associated with a gauge manifold unit.arrow_forwardDescribe the operation of a Bourdon Tube pressure gauge and bellows type pressure gauge?arrow_forward
- When oil pressure is below the spring pressure, the switch opens and the gauge reading falls toward the low-pressure side. Select one: True Falsearrow_forwardChoose True or Falsearrow_forwardödalg äbäi A negative gauge pressure is referred as Vacuum pressure Suction pressure Absolut pressure None of theses O Suction pressure and Vacuum pressurearrow_forward
- Technician A says that a manifold gauge set can be used during the evacuation of the system. Technician B says that a manifold gauge set can be used to diagnose a problem in the A/C system. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardChoose correct answer: In hydraulic system circuit,the pressure gauge would not be available in the power pack. Select one: True Falsearrow_forwardAll gauges operate but read lower than normal: Technician A says that the connection to the instrument cluster may be corroded. Technician B says that the cluster s IVR may be open. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Before installing a gauge on the high-pressure side of a system, you should do which of the following? A. Turn on the system. B. Turn off the system. C. Adjust the system to a neutral position. D. Have a cylinder approved by the DOT nearby.arrow_forwardThe fluid used in bourdon gauge calibration Select one: a. No liquid is used b. Used to transfer the pressure from weights to the gauge c. none d. Used to eliminate frictionarrow_forwardWhat is the use of pressure gauge?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License