Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 6, Problem 10RQ
Technician A uses a digital volt/ohmmeter to test amperage. Technician B uses the same tool to test resistance. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that some small cracks in
the accessory drive belt may be within
tolerance. Technician B says that serpentine
belts can be checked with a wear gauge.
Who is correct?
Select one:
a. Technician A only
b. Technician B only
C. Both A and B
d. Neither A nor B
True or false ?
Which of the following is a digital transducer?
a.
Strain gauge
b.
Thermistor
c.
LVDT
d.
Encoder
Chapter 6 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 6 - Explain why testlights are not recommended for...Ch. 6 - True or False? A compression gauge will show the...Ch. 6 - Name the two basic types of compression gauges.Ch. 6 - What tool is used to test engine manifold vacuum.Ch. 6 - Prob. 5RQCh. 6 - Technician A says that a brake drum micrometer has...Ch. 6 - Technician A says that a pyrometer measures...Ch. 6 - True or False? A lab scope is a visual voltmeter...Ch. 6 - Prob. 9RQCh. 6 - Technician A uses a digital volt/ohmmeter to test...
Ch. 6 - Technician A says that a charging station removes...Ch. 6 - Which of the following statements about manifold...Ch. 6 - True or False? A brake shoe adjusting gauge is an...Ch. 6 - When conducting an oil pressure test: Technician A...Ch. 6 - Which of the following conditions can be revealed...Ch. 6 - Technician A uses a high-impedance testlight on...Ch. 6 - Technician A says that a sulfated and plugged fuel...Ch. 6 - The tests conducted by a scan tool can also be...Ch. 6 - When using a fuel injector pulse tester....Ch. 6 - To measure engine cranking current, a DNIM...Ch. 6 - While discussing a clutch alignment tool....Ch. 6 - True or False? The angle of the drive shaft at the...Ch. 6 - Technician A says that ball joints may be pressed...Ch. 6 - Which of the following is not a suitable way to...Ch. 6 - Prob. 25RQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A uses a testlight to detect resistance. Technician B uses a jumper wire to test circuit breakers, relays, and lights. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardAll gauges operate but read lower than normal: Technician A says that the connection to the instrument cluster may be corroded. Technician B says that the cluster s IVR may be open. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile measuring the resistance of a wire with an ohmmeter: Technician A says that if low resistance is shown on the meter, the wire is shorted. Technician B says that if no resistance is measured, the wire is shorted. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forward
- True or False? The same information available in service manuals and bulletins may also be available electronically on DVDs and the Internet.arrow_forwardTechnician A uses a testlight to test circuit protection devices. Technician B uses a voltmeter to test circuit protection devices. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following tests would not be performed to check for high resistance in the battery' cables? Cranking voltage test Insulated circuit resistance test Starter relay by-pass test Ground circuit resistance testarrow_forward
- Technician A uses a high-impedance testlight on the high-voltage systems in hybrid vehicles. Technician B uses only CAT-III test instruments to check high- voltage systems. Who is correct? Technician A Both A and B Technician B Neither A nor Barrow_forwardWhile checking an A/C compressor clutch coil clamping diode with a DMM, the meter shows infinite resistance when the diode is measured in both directions: Technician A says that the diode is open. Technician B says that all diodes should behave this way until a specified voltage is applied to them. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhile measuring resistance: Technician A uses an ohmmeter to measure resistance of a component before disconnecting it from the circuit. Technician B uses a voltmeter to measure voltage drop. A circuit with very low resistance will drop zero or very little voltage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY