Precision Machining Technology (MindTap Course List)
2nd Edition
ISBN: 9781285444543
Author: Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5.3, Problem 2RQ
A lathe cross slide uses a diameter-reading micrometer collar. If the cross slide is advanced by 0.150". what depth of cut would result?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel
drill. At what speed in revolutions per minute should he operate the drill press?
2. Find the revolutions per minute of an 8 mm drill if it is used to cut an aluminum workpiece using
a high carbon steel drill.
3. The rpm setting of the drill press is set to 600 rpm. What is the maximum diameter in inches of a
high speed drill if it is used to drill a tool steel material?
4. A drill press has the following rpm settings; 350, 600, 1100, & 1600. What rpm setting must be
used if a 15 mm high speed steel drill is used to cut brass workpiece?
5.
A machine operator drills a hole of a 3/8 inch diameter to a stainless steel using a carbon steel
drill. He sets the drill press rpm setting to 900 rpm. Is he operating at correct setting? If not,
then what must be the correct rpm setting considering that the machine has the following rpm
settings of 300, 600, 900, 1200, and 1800?
QUESTION 1
Calculate the spindle speed in RPM of a lathe turning a 96 millimeter diameter material that requires a cutting speed of 148 SMPM.
what is the cutting speed of a shaper having 80 strokes per minute with a length of a stroke at 1.25 feet?
Chapter 5 Solutions
Precision Machining Technology (MindTap Course List)
Ch. 5.1 - List the four main parts of the engine lathe.Ch. 5.1 - What are the two main purposes of the lathe...Ch. 5.1 - What part of the lathe is used to set the feed...Ch. 5.1 - Prob. 4RQCh. 5.1 - Prob. 5RQCh. 5.1 - What is the purpose of the leads crew of a lathe?Ch. 5.1 - What two functions can the lathe tailstock...Ch. 5.1 - The standard taper in most lathe tailstocks is the...Ch. 5.1 - Define the swing and the bed length of a lathe.Ch. 5.2 - What is the special name for the type of jaw-type...
Ch. 5.2 - The most common variation of the above chuck has...Ch. 5.2 - Name two material shapes that can be properly held...Ch. 5.2 - List two advantages of using a self-centering...Ch. 5.2 - Name two material shapes that can be properly held...Ch. 5.2 - List three benefits of holding a workpiece between...Ch. 5.2 - List three potential advantages of using an...Ch. 5.2 - List three characteristics of a workpiece that...Ch. 5.2 - What type of mandrel would be ideal for gripping a...Ch. 5.2 - Name the type of tailstock center that raid be...Ch. 5.2 - What two auxiliary devices can be used to...Ch. 5.2 - Explain the differences between the two auxiliary...Ch. 5.2 - Name the device that is used to transmit the...Ch. 5.2 - Which two tool posts are the most efficient if...Ch. 5.2 - Which device may be used for either toolholding or...Ch. 5.3 - If a 0.050" depth of cut is taken on the diameter...Ch. 5.3 - A lathe cross slide uses a diameter-reading...Ch. 5.3 - In what units are feed rates measured for lathe...Ch. 5.3 - Are deeper cuts used for roughing or finishing...Ch. 5.3 - Calculate spindle RPM and machining time for...Ch. 5.3 - List three safety precautions related to clothing...Ch. 5.3 - What two materials are most commonly used for...Ch. 5.3 - What feature of a lathe cutting tool has a direct...Ch. 5.3 - Is a left-hand or right-hand tool normally used...Ch. 5.3 - What part of the lathe is used to feed the tool...Ch. 5.3 - When facing, why should the tool not be fed past...Ch. 5.3 - Should a left-hand or right-hand tool be used when...Ch. 5.3 - When and how should chips he removed from the work...Ch. 5.3 - What are two reasons for center drilling on the...Ch. 5.3 - When drilling and reaming on the lathe, how are...Ch. 5.3 - How can hole depth be controlled during drilling...Ch. 5.3 - What are two reasons boring may be selected to...Ch. 5.3 - Why must extra care be taken when performing...Ch. 5.3 - How can a tap be aligned when threading a hole on...Ch. 5.3 - Briefly define form cutting.Ch. 5.3 - How do grooving and cutoff speeds compare to...Ch. 5.3 - How can tool binding be overcome when cutting deep...Ch. 5.3 - List the two basic knurl patterns.Ch. 5.3 - How is knurling different from other lathe...Ch. 5.3 - List and briefly describe the two different types...Ch. 5.4 - The distance of actual contact of two mating...Ch. 5.4 - What feature of mating threads determines the...Ch. 5.4 - How many classes of fit are there in the Unified...Ch. 5.4 - Determine the major diameter limits for the...Ch. 5.4 - Determine the minor diameter limits for the...Ch. 5.4 - Determine the pitch diameter limits for the...Ch. 5.4 - Determine the approximate compound-rest in-feed...Ch. 5.4 - What is the name for the rotating device that...Ch. 5.4 - When threading, what is the reason for feeding the...Ch. 5.4 - Prob. 10RQCh. 5.4 - Why should the depth of cut be reduced for each...Ch. 5.4 - What dimension of the thread is measured by using...Ch. 5.4 - What measuring tool is used to visually inspect...Ch. 5.4 - List two applications of Acme threads.Ch. 5.4 - What type of thread is machined on a tapered...Ch. 5.5 - Briefly define a taper.Ch. 5.5 - What is the difference between an included angle...Ch. 5.5 - What does TPI stand for in relation to tapers?Ch. 5.5 - What are the TPI and TPF of a part with end...Ch. 5.5 - What are the corresponding centerline and included...Ch. 5.5 - What is the corresponding centerline angle of a...Ch. 5.5 - What is the limitation of the tool bit taper...Ch. 5.5 - What must be known to use the compound-rest taper...Ch. 5.5 - What taper turning methods allow use of the lathes...Ch. 5.5 - What two steps can be taken to eliminate backlash...Ch. 5.5 - The TPI specified on a print is 0.030". If...Ch. 5.5 - If TPF is 0.42", how much movement should register...Ch. 5.5 - What is the benefit of using the offset tailstock...Ch. 5.5 - What are two ways to reduce uneven pressure on...Ch. 5.5 - Calculate tailstock setover for a 13.5" part with...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- If a 0.050" depth of cut is taken on the diameter of a workpiece, by how much will the diameter be reduced?arrow_forward-How many holes require drilling? -What is the center to center distance of the 6mm tapped holes? -What tap drill is used for holes marked Z? -How many surfaces are machine finished? -What are the dimensions of the face marked F & C? -What are the dimensions have symbols A, E &, B -In what dihedral angle is the drawing made? -What is the max and min dimensions of D -What is the tolerance of measurement D?arrow_forwardFind the commercial tap drill size for 1⁄2”-20 NF bolt.arrow_forward
- I need help matching each drawing to the term that it describes. Answers are used only once.arrow_forwardQ24. For the below figure please write its part program. The depth of the cut is 0.25 inches (Finishing operation), while the tool's diameter is 0.5 inches. Consider the speed and feed. -0.75- - - 1.0 60⁰ RO.25 (0, 0) 0.75-arrow_forwardWhat depth of cut is needed for a ¾ inch wide keyway in a 3 inches diameter shaft?arrow_forward
- Find the end mill diameter for slotting operation by a cutting speed of 18 meter /minute and spindle speed of 260 rpm. End mill diameter in mm =arrow_forwardis the lathe operation, which is performed without the cutting tool moving parallel to the axis of workpiece. Grooving Operation O Boring Operation Counter Boring Thread cuttingarrow_forwardSolve First one Onlyarrow_forward
- It is required to cut screw threads of 2 mm pitch on a lathe. The lead screw has a pitch of 6 mm. If the spindle speed is 60 rpm, then the speed of the lead screw will bearrow_forwardWhat is the cutting speed of turning in the unit of m/min, when main axis spindle speed is 2,409 rpm and external diameter is 86mm ? Answer in 2 decimal points. Calculate the theoretical spindle rotational speed in rpm required to drill a 1 mm hole in copper using high speed steel drill. The recommende cutting speed is as following. The thickness of the copper plate is 24. (Leave the answer in numerical value, no need to key in 'rpm') Typical cutting speeds (m/min) High speed steel Material Tungsten carbide Aluminum 100 500 60 330 Copper Hard brass 45 230 Bronze 35 180 Mild steel 28 250 Cast iron 20 160arrow_forwardWrite TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the sentence incorrect and write its corresponding correct answer. 16. since the thickness of chips is always greater than the depth of cut, chip compression ratio is àways less than 1.0. 17. Inserts have multiple cutting points. 18. Free Machining steels are non-ferrous metals which contain sulfur and phosphorus.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY