While installing new brake pads: Technician A coats the inside diameter of the bushings with silicone grease before installing the mounting bolts and sleeves of floating calipers. Technician B lubricates the caliper ways on the caliper support and the mating parts of the sliding caliper housings with the recommended lubricant. Who is correct?

Q: Road test Report is Overhaul all four-wheel brakes and the Universal joints After the maintenance…

A: Option - B , D  => After operation is completed the road test report will happen to check the…

Q: In a typical drum brake, which component provides afoundation for the brake shoes and…

A: Given Data : Typical drum brake

Q: Which of the following statements about drum brakeshoes is not true?a. Web thickness varies only…

A: Brake shoes are a major part of a drum brake system. these crescent-shaped components are made up of…

Q: frictions doesnot depend on surface area of contact if so,why does a tyre not flat?

A: Friction does not depend on the surface area of contact. It only depends on the weight of the body…

Q: (1)The brake mean effective pressure? (2) the mechanical effeciency

A:

Q: Which of the following is not a factor in determiningthe effectiveness of a brake system?a. Heat…

A: Given Data : Effectiveness of brake system

Q: Automotive technology Backing plates, struts, levers, and other metal brake parts should be Select…

A: Given: How the various automotive parts should be cleaned.

Q: Explain the operation and maintenance considerations for the foot brake assembly from the Harrison…

A: Given Foot Brake To find Operation Maintenance

Q: * The number 8 is pointed to 10 brake drum. brake pad lining. brake caliper piston. brake caliper.…

A: The number 8 is pointed to brake shoe lining.

Q: How does air-over Hydraulic brake system work

A: Air brakes are much easier to attach than hydraulic brakes, and using air rather than hydraulic…

Q: When examining disc brakes: Technician A visually inspects the rotor and says that the rotor can be…

A: Technician A is correct.

Q: Name the two methods of attacking brake lining materials to the brake shoes.

A: Given Data : Break lining materials Assumptions made in solution : In solution, it is assumed that…

Q: Discbrake friction linings are sometimes called brake The ratio of the force required to slide one…

A: Given questions are related to IC engines and Machine design             [Note : According to…

Q: What’s is the purpose of breaking in new disc pads

A:

Q: How can you give the effect of the hydraulic brake

A: Given Data : Effect of hydraulic break

Q: G. Brake shoes Energy of motion H. Brake pads Operates the brakes on opposite comers of the vehicle…

A: Match Of the following  ****As per company policy we are supposed to do only three subparts if you…

Q: Most vehicles built to use brake on one wheel two wheels only side each wheel O other: tyre in the…

A:

Q: 67. Which of these angles is adjusted last during a wheel alignment? a. Steering axis inclination c.…

A: " Since you have asked multiple questions we will solve the first question for you. If you want any…

Q: echnician a says that the malfunction of the ABS can cause the control module to shut off or…

A: Who is correct?

Q: When performing the air brake system leakage test, the Certified Inspector must reject the vehicle…

A: Answer = False

Q: What are the general sources of error when using Vernier Caliper? when using Micrometer Caliper?

A:

Q: Disc brakes are not as likely to fade during heavy braking as are drum brakes. True OR False?

A: Given Data : Disc Brakes  Drum Brakes

Q: After draining gear oil from a transaxle, the techniciannotices that the oil has shiny, metallic…

A: For a transmission or axle to last longer, it needs to be properly lubricated. After the required…

Q: What are the risks of working with brake fluid?

A: Brake fluid is generally made with glycol or silicone. Bothe material is dangerous for us.

Q: fferent parts of the brakes system of an off-road bicycle

A: introduction  In the marine and seaward industry, plan and hardware setups fluctuate from one…

Q: The rotating yellow part is

A:

Q: Technician A says a metric bolt with the marking of 8.9 has more yield strength than a 10.9 bolt.…

A: Technician A is not correct as the 10.9 grade bolt has more strength than 8.9 grade. Grade 10.9 is…

Q: that used in the part of the suspension system O drive shaft oil spring O camshaft Other:

A: 7. ............ that is used in the part of the suspension system

Q: if you read the scan code on the vehicle and u0121 was present what would be the problem in brakes

A: Solution:      Code U1021 generally refers to a communication problem between the ABS brake control…

Q: Pre-alignment check is done before checking or adjusting the front-end alignment. One of the pre-…

A: Given question: Explain all tire conditions that need to be checked in detail.

Q: b) Draw a neat sketch showing the linkage to operate brake master cylinder and describe the same

A: The master cylinder is an important part of the braking system of an automobile. The main valve…

Q: Technician A says that a hard brake pedal on a vehicle with disc brakes can be caused by air in the…

A: Option d is correct. Neither A nor B.

Q: What are the two basic types of brake rotors used on today’s vehicles?

A: Two basic types of brake rotor used in today vehical is, 1. Blank and smooth type of rotor. 2.…

Q: Technician A cleans brake components  in denatured alcohol. Technician B cleans brake components in…

A: Technician A cleans brake components in denatured alcohol. Technician B cleans brake components in…

Q: J. Pascal's law K. Hygroscopic L DOT wet specification M. DOT dry specification N. Longitudinal…

A: As per the instructions the A-I already answered. Below from J-R matches are explained : J) Pascal's…

Q: When discussing CV axle replacement, Technician A states that once a CV boot is torn the entire CV…

A: The normal problem with CV joints is in protection of boot cracks, tears. As it happens, the grease…

Q: .a) Explain the purpose of the brake assist system and the traction control system. b) Explain how…

A: Brake Assist System (BAS):The purpose of the Brake Assist System is to enhance braking performance…

Q: Question-3 The following illustration shows the construction parts of the disc brake. From the…

A:

Q: Explain how a duo-servo brake assembly works to provide greater braking compared to leading and…

A: To explain: Explain how a duo-servo brake assembly works to provide greater braking compared to…

Q: Which of the following would NOT be cause for rejection when checking the tire condition

A: Answer = option (c) All of the statements shown are cause for rejection

Q: S. Brake fade T. Unsprung weight U. Metering valve V. Bulkhead W. Fire wall X. ABS Y. Pads Z. Equal…

A: As per the instructions A-R answers are already given. here below S- AA  solutions are given :  G )…

Lubricants

Lubricant can be expressed as the substance that is applied among surfaces to control the wear and tear and improve performance. Lubricants play an essential part in the safety of machinery components like gears, shaft, linkage, cam, clutches, and many others. The quantities which affect the amount of lubricant are temperature, surrounding conditions, speed of the components, and many more.