Explanation Given information: The length of the tube is 2 m. Calculation: Refer the shear stress-strain diagram. The value of yield shear stress is 350 MPa and the value of yield shear strain is 0.007 rad. The expression to find the plastic torque ( T P ) in the shaft with outer radius ( c 0 ) and inner radius ( c i ) is shown below: T P = 2 π τ Y ∫ c i c 0 ρ 2 d ρ = 2 π τ Y [ ρ 3 3 ] c i c 0 = 2 π τ Y ( ( c 0 ) 3 3 − ( c i ) 3 3 ) (1) The value of outer radius is 100 mm and the value of inner radius is 60 mm. Substitute 350 MPa for τ Y , 100 mm for c 0 , and 60 mm for c i in Equation (1). T P = 2 π ( 350 MPa ) ( ( 100 mm ) 3 3 − ( 60 mm ) 3 3 ) = 2 π ( 350 MPa × 1 N mm 2 1 MPa ) ( ( 100 mm ) 3 3 − ( 60 mm ) 3 3 ) = 574.702 × 10 6 N ⋅ mm = 574.7 kN ⋅ m Therefore, the torque required for the material to become fully plastic is 574.7 kN ⋅ m _ . The radius of the tube at yield ( ρ Y ) is 60 mm . Find the angle of twist ( ϕ P ) of the tube using the relation: ϕ P = γ Y ρ Y L (2) Here, L is the length of the tube. Substitute 0.007 rad for γ Y , 60 mm for ρ Y , and 2 m for L in Equation (2). ϕ P = 0.007 rad 60 mm ( 2 m ) = 0.007 rad 60 mm ( 2 m × 10 3 mm 1 m ) = 0.2333 rad Find the value of the shear modulus of elasticity of the material ( G ) using the relation: G = τ Y γ Y (3) Substitute 350 MPa for τ Y and 0.007 rad for γ Y in Equation (3). G = 350 MPa 0.007 rad = 50 × 10 3 MPa = 50 × 10 3 MPa ( 10 6 Pa 1 MPa ) = 50 × 10 9 Pa Find the angle of twist ( ϕ ' P ) of the tube when the reverse torque of 574

10th Edition

ISBN: 9780134319650

Author: Russell C. Hibbeler

Publisher: PEARSON

See similar textbooks

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational…

Videos

Question

Chapter 5.10, Problem 5.140P

To determine

The torque required for the material to become fully plastic.

The permanent angle of twist of the tube.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 5.10, Problem 5.139P

Chapter 5.10, Problem 5.141P

Students have asked these similar questions

6: Refer to the figure.Given: W1 = 200 kN/m; W2 = 300 kN/m; L1 = 2 m; L2 = 3 m; L3 = 2 m(a) Calculate the total length L so that the resulting upward pressureq is uniform. (b) draw the shear and moment diagram and determinethe maximum shear, maximum positive and negative bendingmoments.

A six cylinder, four-stroke diesel engine develops a power of 200 kW at 2000 rpm. The bsfc is 0.2 kW/kg h of fuel with 34.9° API. The fuel is injected at an average pressure of 350 bar and the pressure in the combustion chamber is 40 bar. Assuming Ca for injector 0.75 and the atmospheric pressure 1 bar. Determine the period of injection in seconds if the total orifice area required per injector is 0.4876 × 10-6 m².

Trieed a detailed drawing Win explanatio LL Antsmi 1981x pu + 96252 اه 6. The Pre-combustion chamber design engines employ nozzle type commonly referred to as a ....... a. inward-opening nozzle b. multiple-hole nozzle. c. pintle nozzle. d. none of these. 7. If the temperature of the spark plug tip is less than 350 °C, ......... a. the plug might not work. b. the carbon deposits would increase. 8. Port injection sprays fuel....... c. pre-ignition will occur. d. none of these. a. towards the intake valve. b. in the engine cylinder. c. in the throttle body assembly. d. none of these. 9. When the fuel-air mixture changed from best power to a richer ratio, the spark advance should be........ a. increased. b. decreased. c. left unchanged. d. none of these. d. none of these. 10. Spark plugs are classified as hot plugs and cold plugs depending upon ........ a. spark gap. b. the type of plug c. the operating temperature insulator. range of the electrode tip. ---20125 750 x2.01 SP 5.

Chapter 5 Solutions

Mechanics of Materials (10th Edition)

Ch. 5.3 - Determine the internal torque at each section and...Ch. 5.3 - Determine the. internal torque at each section and...Ch. 5.3 - The solid and hollow shafts are each subjected to...Ch. 5.3 - The motor delivers 10 hp to the shaft. If it...Ch. 5.3 - The solid circular shaft is subjected to an...Ch. 5.3 - The hollow circular shaft is subjected to an...Ch. 5.3 - The shaft is hollow from A to B and solid from B...Ch. 5.3 - Determine the maximum shear stress in the...Ch. 5.3 - Determine the maximum shear stress in the shaft at...Ch. 5.3 - Determine the shear stress a: point A on the...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The torque required for the material to become fully plastic. The permanent angle of twist of the tube.

Solution Summary: The author explains the torque required for the material to become fully plastic and the permanent angle of twist of the tube.