Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 51, Problem 10RQ
Brake linings should be replaced when.
- linings are worn to within */3’ inch of a rivet head
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Brake linings should be replaced when __ .a. linings are worn to within 1 /32 inch of a rivet headb. linings are contaminated with oil or greasec. linings are contaminated with brake fluidd. all of the above
Which of the following would NOT be cause for rejection when checking the tire condition?
Any tire has a fabric break or cut exposing ply or cord or any tire is in contact with the body or frame.
Any tire tread or recap is separated or any tire is flat.
All of the statements shown are cause for rejection.
Any tire has any bumps, bulges, or knots or is repaired with a boot or blowout patch.
When performing the air brake system leakage test, the Certified Inspector must reject the vehicle if the system does not maintain 100 P.S.I. (Perform this test for 1 minute with the brakes fully applied & the engine running on single and/ or combination vehicles). True or False?
Chapter 51 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 51 - Name the two methods of attaching brake lining...Ch. 51 - Explain how drum brakes create a self-multiplying...Ch. 51 - List at least five separate types of wear and...Ch. 51 - What is the job of wheel cylinder stops?Ch. 51 - Explain the operation of an integral drum brake...Ch. 51 - In a typical drum brake, which component provides...Ch. 51 - True or False? The name duo-servo drum brake is...Ch. 51 - Prob. 8RQCh. 51 - Which of the following statements about drum brake...Ch. 51 - Brake linings should be replaced when. linings are...
Ch. 51 - In the unapplied position, drum brake shoes arc...Ch. 51 - Duo-servo drum brakes are also known as what type...Ch. 51 - On most vehicles, the automatic adjuster cables or...Ch. 51 - Backing plates, struts, levers, and other metal...Ch. 51 - A buildup of brake dust and dirt between the...Ch. 51 - Technician A says that an out-of-round drum can...Ch. 51 - Technician A says that a grinding noise from a...Ch. 51 - It has been determined that chatter and brake pull...Ch. 51 - Technician A says that the discard dimension of a...Ch. 51 - After resurfacing a brake drum: Technician A...Ch. 51 - Drum linings are badly worn at their heel and toe:...Ch. 51 - When machining brake drums: Technician A tries to...Ch. 51 - While discussing what would happen if too much...Ch. 51 - Technician A checks the surface of the drum for...Ch. 51 - While discussing pull during braking: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- After resurfacing a brake drum: Technician A cleans it using hot water and a lint-free cloth. He then uses compressed air to thoroughly dry it Technician B cleans the drum using a lint-free cloth dipped in a special brake cleaning solvent. She then allows the drum to dry before reinstallation. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardWhich of the following can lead to brake hose failure? Improperly matched fittings Stressing the hose during installations Deterioration from heat and contaminants All of the abovearrow_forwardTrue or False? If brake fluid is discolored, the system must be flushed and the fluid replaced.arrow_forward
- True or False? Backing plates, struts, levers, and other metal brake parts should be cleaned with a wet-cleaned using water or a water-based solution.arrow_forwardTrue or False? A brake shoe adjusting gauge is an inside-outside measuring device used to initially adjust the expanse of brake shoes before the brake drum is installed.arrow_forwardWhich of the following is not a suitable way to bleed an entire hydraulic brake system? Manual bleeding Bench bleeding Pressure bleeding Vacuum bleedingarrow_forward
- Backing plates, struts, levers, and other metal brake parts should be. wet-cleaned using water or a water-based solution wet-cleaned using an alcohol-based solvent wet-cleaned using gasoline dry-cleaned onlyarrow_forwardTrue or False? If brake fluid is dark or brown colored. the system must be flushed and the fluid replaced.arrow_forwardTechnician A says that the discard dimension of a brake drum is the drums allowable machining dimension. Technician B says that the discard dimension is the allowable wear dimension. There must be 0.030 inch left for wear after machining. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- The basic frictional parts of a brake system are being discussed: Technician A says that the harder the frictional parts are pushed together, the higher the friction. Technician B says that the harder the frictional parts are pushed together, the more heat is developed. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardTechnician A says that replacement wheel rims should be the same as the original equipment wheels in load capacity, offset, width, diameter, and mounting configuration. Technician B says that if wheels are installed that have a different stock width or diameter, make sure to use a tire that has the same overall width as the original tires. Otherwise the vehicles wheel-speed sensors, speedometer, antiock brake system, and many other systems will be affected. Who is correct? a. Technician A only b. Technician B only c. Both A and B Neither A nor Barrow_forwardWhich of the following statements about drum brake shoes is not true? Web thickness varies only with changes in shoe size. Many shoes have indented places along the edge of the rim. The shoe rim is welded to the web. The primary/leading shoe is typically the one that is positioned toward the front of the vehicle.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License