To determine the flow through the siphon when h =4 ft and plot the HGL and EGL for the siphon conduit. Explanation Given: The height of siphon from the inlet ( h ) is 4 ft. The diameter of the siphon ( d ) is 8 in . . The temperature of the water is 80 ° F . Calculation: Consider the water is incompressible and inviscid and the steady flow state. The point A and B are open to atmosphere, the velocity at point A and B are zero. p A = p B = 0 Consider the capacity of water in the reservoir the velocity of the water at point A is negligible. V A ≃ 0 The datum passed through the Point B, z B = 0 The datum level at point A is, z A = 38 ft − 2 ft =36 ft Apply the Bernoulli's equation between the point A and B. p A γ w + V A 2 2 g + z A = p B γ w + V B 2 2 g + z B 0 + 0 + 36 ft = 0 + V B 2 2 ( 32.2 ft / s 2 ) + 0 V B = 48.15 ft/s The cross section of the point C and B are same. So the velocities at these points are also same. V C = V B = 48.15 ft/s Apply the Bernoulli's equation between the point A and C. p A γ w + V A 2 2 g + z A = p C γ w + V C 2 2 g + z C 0 + 0 + 36 ft = p c 62.4 lb/ft 3 + ( 48.15 ft/s ) 2 2 ( 32.2 ft / s 2 ) + 30 ft p C = ( − 1872 lb ft 2 ) ( 1 ft 12 in

2nd Edition

ISBN: 9780134649290

Author: Russell C. Hibbeler

Publisher: PEARSON

See similar textbooks

Videos

Question

Chapter 5, Problem 76P

To determine

the flow through the siphon when h =4 ft and plot the HGL and EGL for the siphon conduit.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 5, Problem 75P

Chapter 5, Problem 77P

Students have asked these similar questions

Assume the Link AO is the input and revolves 360°, determine a. the coordinates of limit positions of point B, b. the angles  (AOC) corresponding to the limit positions

oyfr 3. The figure shows a frame under the influence of an external loading made up of five forces and two moments. Use the scalar method to calculate moments. a. Write the resultant force of the external loading in Cartesian vector form. b. Determine the & direction of the resultant moment of the external loading about A. 15 cm 18 cm 2.2 N-m B 50 N 45° 10 cm 48 N.m 250 N 60 N 20 21 50 N 25 cm 100 N A 118, 27cm 5, 4:1

The 2-mass system shown below depicts a disk which rotates about its center and has rotational moment of inertia Jo and radius r. The angular displacement of the disk is given by 0. The spring with constant k₂ is attached to the disk at a distance from the center. The mass m has linear displacement & and is subject to an external force u. When the system is at equilibrium, the spring forces due to k₁ and k₂ are zero. Neglect gravity and aerodynamic drag in this problem. You may assume the small angle approximation which implies (i) that the springs and dampers remain in their horizontal / vertical configurations and (ii) that the linear displacement d of a point on the edge of the disk can be approximated by d≈re. Ө K2 www m 4 Cz 777777 Jo Make the following assumptions when analyzing the forces and torques: тв 2 0>0, 0>0, x> > 0, >0 Derive the differential equations of motion for this dynamic system. Start by sketching LARGE and carefully drawn free-body-diagrams for the disk and the…

Chapter 5 Solutions

Fluid Mechanics (2nd Edition)

Ch. 5 - Prob. 1FP Ch. 5 - Oil is subjected to a pressure of 300 kPa at A,...Ch. 5 - Prob. 3FP Ch. 5 - Water flows through the pipe at 8 m/s. Determine...Ch. 5 - The tank has a square base and is filled with...Ch. 5 - Prob. 6FP Ch. 5 - Water flows from the reservoir through the...Ch. 5 - Crude oil flows through the 50-mm-diameter pipe...Ch. 5 - Water at A has a pressure of 400 kPa and a...Ch. 5 - Water from the reservoir flows through the...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.