EBK MATERIALS FOR CIVIL AND CONSTRUCTIO
4th Edition
ISBN: 8220102719569
Author: ZANIEWSKI
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 5.24QP
Referring to Table 5.6, plot the specification limits of Superpave gradation with a nominal maximum size of 19 mm on a 0.45 gradation chart (Figure A.25). What is the maximum aggregate size of this gradation? Is this a dense, open, or gap graded gradation? Why?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
a. For an aggregate sample, if you know that the apparent relative density is 2.72 and the water absorption is 1.2%. The dry mass of the aggregate is 514 gm. Find the bulk and saturated surface dry (SSD) relative density values?
b. Why does the maximum size of aggregate depend on the clear spacing between bars? Show with a simple sketch.
Note: Please answer both a and b... Please answer the both questions.. I don't want single b answer.. thank you
A sieve analysis test was performed on a sample of coarse aggregate and produced the results in Tablea. Calculate the percent passing through each sieve.b. What is the maximum size?c. What is the nominal maximum size?d. Plot the percent passing versus sieve size on a semilog gradation chart.e. Plot the percent passing versus sieve size on a 0.45 gradation chart.f. Referring to Table (ASTM C33), what is the closest size number anddoes it meet the gradation for that standard size?
Find 4 published values for bulk density for small coarse aggregate, and quote their references.
Chapter 5 Solutions
EBK MATERIALS FOR CIVIL AND CONSTRUCTIO
Ch. 5 - Prob. 5.1QPCh. 5 - Discuss five different desirable characteristics...Ch. 5 - Discuss five different desirable characteristics...Ch. 5 - The shape and surface texture of aggregate...Ch. 5 - Define the following terms: a. Saturated...Ch. 5 - Three samples of fine aggregate have the...Ch. 5 - A sample of wet aggregate weighed 297.2 N. After...Ch. 5 - 46.5 kg (102.3 lb) of fine aggregate is mixed with...Ch. 5 - Samples of coarse aggregate from a stockpile are...Ch. 5 - Base course aggregate has a target dry density of...
Ch. 5 - Calculate the percent voids between aggregate...Ch. 5 - Calculate the percent voids between aggregate...Ch. 5 - Coarse aggregate is placed in a rigid bucket and...Ch. 5 - The following laboratory tests are performed on...Ch. 5 - Students in the materials lab performed the...Ch. 5 - The specific gravity and absorption test (ASTM...Ch. 5 - Prob. 5.18QPCh. 5 - Calculate the sieve analysis shown in Table P5.19...Ch. 5 - Calculate the sieve analysis shown in Table P5.20,...Ch. 5 - A sieve analysis test was performed on a sample of...Ch. 5 - A sieve analysis test was performed on a sample of...Ch. 5 - Draw a graph to show the cumulative percent...Ch. 5 - Referring to Table 5.6, plot the specification...Ch. 5 - Referring to the aggregate gradations A, B, and C...Ch. 5 - Table P5.26 shows the grain size distributions of...Ch. 5 - Table P5.27 shows the grain size distributions of...Ch. 5 - Three aggregates are to be mixed together in the...Ch. 5 - Table P5.29 shows the grain size distribution for...Ch. 5 - Laboratory specific gravity and absorption tests...Ch. 5 - Table P5.31 shows the grain size distribution for...Ch. 5 - Prob. 5.32QPCh. 5 - Laboratory specific gravity and absorption tests...Ch. 5 - Prob. 5.34QPCh. 5 - Define the fineness modulus of aggregate. What is...Ch. 5 - Calculate the fineness modulus of aggregate A in...Ch. 5 - Calculate the fineness modulus of aggregate B in...Ch. 5 - A portland cement concrete mix requires mixing...Ch. 5 - Discuss the effect of the amount of material...Ch. 5 - Aggregates from three sources having the...Ch. 5 - Aggregates from three sources having the...Ch. 5 - A contractor is considering using three stockpiles...Ch. 5 - Prob. 5.43QPCh. 5 - What are the typical deleterious substances in...Ch. 5 - Review ASTM D75 and summarize the following: a....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Students in the materials lab performed the specific gravity and absorption test (ASTM C127) on coarse aggregate and they obtained following data: a. Dry weight = 3862.1 g b. SSD weight = 3923.4 g c. Submerged weight = 2452.1 g 1. Calculate the specific gravity values (dry bulk, SSD, and apparent) and the absorption of the coarse aggregate. (Answer in 3 decimal places)arrow_forwardGive the conclusion and recommendation of this experiment: DETERMINATION OF SPECIFIC GRAVITY AND ABSORPTION OF FINE AGGREGATES.arrow_forwardif my Fineness modulus for fine aggregates is 1.88, does it meet the standards fineness modulus for dine aggregates? And if my Fineness modulus for coarse aggregate is 2.61, does it also meet the standards? Explainarrow_forward
- Distinguish porosity from voids content for aggregate with the help of schematic diagrams.arrow_forwardLaboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have to be blended. The results are as follows:Aggregate A: Bulk specific gravity = 2.814; Absorption = 0.4% Aggregate B: Bulk specific gravity = 2.441; Absorption = 5.2% a. What is the specific gravity of a mixture of 50% aggregate A and 50% aggregate B by weight? b. What is the absorption of the mixture?arrow_forwardWhat are the possible conclusion in specific gravity and absorption of coarse aggregates?arrow_forward
- Specific Gravity and Absorption of Coarse Aggregates What are the possible discussion of observations for specific gravity and absorption of aggregate to observed values?arrow_forwardFor fine aggregate: bulk specific gravity=2.60, SSD Bulk Specific Gravity=2.63, apparent Specific gravity= 2.68, percent absorption=1.54% For coarse aggregate= bulk specific gravity= 2.62, SSD specific gravity=2.63, apparent specific gravity= 2.65, percent absorption=1.70% From the data above, what can you conclude about these bulk aggregate, ssd bulk specific gravity, apparent specific gravity, and percent absorption? What is the effect of these value in concrete?arrow_forwardIf you don't no the solution please leave it. I want right solution according to the questionarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill Education
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning
Aggregates: Properties; Author: nptelhrd;https://www.youtube.com/watch?v=49yGZYeokKM;License: Standard YouTube License, CC-BY