Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 5, Problem 19MC
Which of the following is not measured with a feeler gauge set?
- Piston ring side clearance
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
1
Which of the following is not measured with a feelergauge set?a. Piston ring side clearanceb. Flywheel runoutc. Crankshaft end playd. Spark plug gap
True or False? The camshaft is always locatedin the engine block.
Chapter 5 Solutions
Automotive Technology
Ch. 5 - Explain how to properly use and care for a...Ch. 5 - List some common uses ot the dial indicator.Ch. 5 - Wrenches are available in several styles. List and...Ch. 5 - How do manufacturers inform technicians about...Ch. 5 - Prob. 5SACh. 5 - Describe three sources of service information...Ch. 5 - Prob. 1MCCh. 5 - Which of the following wrenches is the best choice...Ch. 5 - Technician A says that a micrometer can be used to...Ch. 5 - Prob. 4MC
Ch. 5 - Which of the following screwdrivers is like a...Ch. 5 - Technician A says most US bolts have a thread...Ch. 5 - Technician A uses a punch to align holes in parts...Ch. 5 - An extractor is used for removing broken. seals...Ch. 5 - Prob. 9MCCh. 5 - Technician A uses a blowgun to blow off parts...Ch. 5 - Technician A says that flare nut or line wrenches...Ch. 5 - Technician A uses a dial indicator to take inside...Ch. 5 - For a measurement that must be made within one...Ch. 5 - Technician A says that jack stands should always...Ch. 5 - When using an air impact wrench. Technician A uses...Ch. 5 - While discussing thread sealants and lubricants:...Ch. 5 - The metric equivalent to 10 miles is. 0.06895 bar...Ch. 5 - Which of the following thread designs typically...Ch. 5 - Which of the following is not measured with a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A checks crankshaft oil clearance with a feeler gauge. Technician B uses a dial indicator to check crankshaft oil clearance. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue False? Camshaft straightness is checked using V-blocks and a feeler gauge?arrow_forwardTrue or False? The camshaft is always located in the engine block.arrow_forward
- True or False? Valve lash is adjusted in many different ways; however, on many OHC engines, the clearance is set by replacing a shim.arrow_forwardWhich of the following statements is incorrect? Cylinder head bolts must be tightened to the proper amount of torque. Most cylinder head bolts are tightened in a sequence that starts on one end. On some engines, the head bolts are retorqued after the engine has been run and is hot. Many engines use head bolts of different lengths.arrow_forwardWhile preparing to remove an engine: Technician A turns the crankshaft pulley to set the engine at number 1 cylinder TDC. Technician B removes the drive belt and crankshaft pulley. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While determining the most likely problem of an engine with poor compression test results but acceptable cylinder leakage readings: Technician A says that the problem may be incorrect valve timing. Technician B says that the problem is worn valve seats. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile determining the cause for air leaking out of the oil throttle body during a cylinder leakage test: Technician A says that a burnt intake valve is indicated. Technician B says that a warped cylinder head or bad head gasket is indicated. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forwardWhich spark plug always has a tapered seat? 12 mm 14 mm 16 mm 18 mmarrow_forward
- Technician A says that crankshaft counterweights offset the weight of the connecting rods and pistons. Technician B says that crankshaft counterweights are used to dampen crankshaft torsional vibrations. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forwardWhat problem may result from dirt buildup on an engines throttle plates?arrow_forwardWhich of the following statements about the purpose of a cylinder head gasket is not true? It seals intake stroke vacuum, combustion pressure, and the heat of combustion. It prevents coolant leakage and resists rust, corrosion and, in many cases, meters coolant flow. It allows for lateral and vertical head movement as the engine heats and cools. It meters lubricating oil onto the engines cylinder walls.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License