Fluid Mechanics: Fundamentals and Applications
4th Edition
ISBN: 9781259877827
Author: CENGEL
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 10P
Consider the flow of an incompressible Newtonian fluid between two parallel plates that are 4 mm apart. If the upper plate moves to right with u1= 5 m/s while the bottom one moves to the left with u2 = 1.5 m/s, what would be the net flow rate at a cross-section between two plates? Take the plate width to be 5 cm.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Air flows at the rate of 1.5m/s through a horizontal pipe with a gradually reducing cross-section
as shown in the figure. The two cross-sections of the pipe have diameters of 400mm and 200 mm.
Take the air density as 1.2 kg/m³ and assume inviscid incompressible flow. The change in
pressure (P2-Pj) (in kPa) between sections 1 and 2 is
200mm
! (1) ↑
Air Flow
400mm
(2)
1.5 m³ /s
(A) –1.28
(B) 2.56
(C) -2.13
(D) 1.28
(1) Basic Concepts
Show that a stress and a momentum flux have the same unit by showing that
a force and the rate of momentum change or transfer have the same unit.
(2) Overall Mass Balance Equation
An incompressible fluid is flowing through a circular conduit, as shown in the
figure below Fig P1.2-1. The velocity profile of the fluid in the 8-cm-diameter
pipe is
v, = 0.1
ст/s
What is the average velocity in the 2-cm-diameter pipe?
2cm
8cm
Tube
(3) Overall Momentum Balance Equation
Ahorizontal turbulent liquid jet of diameter Dand average velocity v, impinges
on a vertical plate mounted on a cart, thus exerting a force F on a plate, as
shown in Fig. P1.4-3. Determine the opposing force needed to keep the plate
moving at a constant velocity v, (< v). Neglect the viscous and gravity forces.
(Hint: Let the control volume Q move with the plate)
Plate
Nozzle
1|Page
(4) Differential Momentum Balance Equation
Consider the incompressible Newtonian fluid flowing, under the pressure
gradient…
Petrol (ρ=750 kg/m3) flows through a pipeline with inlet diameter 8 cm and outlet diameter 4 cm. The inlet and outlet gauge pressures measured to be 400 kPa and 130 kPa respectively. Assuming the pipeline to be horizontal and neglecting friction, calculate the outlet velocity (V2) of water by using continuity and Bernoulli’s equation.
Chapter 5 Solutions
Fluid Mechanics: Fundamentals and Applications
Ch. 5 - Does the amount of mass entering a control volume...Ch. 5 - Define mass and volume flow rates. How are they...Ch. 5 - Name four physical quantities that are conserved...Ch. 5 - When is the flow through a control volume steady?Ch. 5 - Consider a device with one inlet and one outlet....Ch. 5 - A hair dryer is basically a duct of constant...Ch. 5 - A garden hose attached with a nozzle is used to...Ch. 5 - Air whose density is 0.082 Ibm/ft3 enters the duct...Ch. 5 - A 0.7$-m3 rigid tank initially contains air whose...Ch. 5 - Consider the flow of an incompressible Newtonian...
Ch. 5 - A desktop computer is to be cooled by a fan whose...Ch. 5 - The minimum fresh air requirement of a residential...Ch. 5 - The ventilating fan of the bathroom of a building...Ch. 5 - Air enters a nozzle steadily at 2.21 kg/m3 and 20...Ch. 5 - Air at 40°C flow steadily through the pipe shown...Ch. 5 - In climates with low night-time temperatures, an...Ch. 5 - What is mechanical energy? How does it differ from...Ch. 5 - Define turbine efficiency, generator efficiency,...Ch. 5 - What is mechanical efficiency? What does a...Ch. 5 - How is the combined pump-motor efficiency of a...Ch. 5 - Prob. 21PCh. 5 - A differential thermocouple with sensors at the...Ch. 5 - Electric power is to be generated by installing a...Ch. 5 - Consider a river flowing toward a lake at an...Ch. 5 - Express the Bernoulli equation in three different...Ch. 5 - What are the three major assumptions used in the...Ch. 5 - Define static, dynamic, and hydrostatic pressure....Ch. 5 - What is streamwise acceleration? How does it...Ch. 5 - What is stagnation pressure? Explain how it can be...Ch. 5 - Define pressure head, velocity head, and elevation...Ch. 5 - How is the location of the hydraulic grade line...Ch. 5 - Prob. 33CPCh. 5 - What is the hydraulic grade line? How does it...Ch. 5 - A glass manometer with oil as the working fluid is...Ch. 5 - The velocity of a fluid flowing in a pipe is to be...Ch. 5 - The water level of a tank on a building roof is 20...Ch. 5 - Prob. 38CPCh. 5 - Prob. 39CPCh. 5 - In a hydroelectric power plant, water enters the...Ch. 5 - A Pitot-static probe is used to measure the speed...Ch. 5 - The air velocity in the duct of a heating system...Ch. 5 - A piezometer and a Pitot tube are tapped into a...Ch. 5 - The diameter of a cylindrical water tank is D0and...Ch. 5 - A siphon pumps water from a large reservoir to a...Ch. 5 - Water flows through a horizontal pipe at a rate of...Ch. 5 - An airplane is flying at an altitude of 10.500 m....Ch. 5 - While traveling on a dirt road, the bottom of a...Ch. 5 - The water in an 8-rn-diameter, 3-rn-high...Ch. 5 - Reconsider Prob. 5-49. Determine how long it will...Ch. 5 - Air at 105 kPa and 37°C flows upward through a...Ch. 5 - Water at 20°C is siphoned from a reservoir as...Ch. 5 - The water pressure in the mains of a city at a...Ch. 5 - A pressurized tank of water has a 10-cm-diameter...Ch. 5 - Air is flowing through a venturi meter whose...Ch. 5 - The water level in a tank is 20 m above the...Ch. 5 - The air velocity in a duct is measured by a...Ch. 5 - In cold climates, water pipes may freeze and burst...Ch. 5 - Prob. 61PCh. 5 - A fluid of density and viscosity flows through a...Ch. 5 - What is the minimum diameter at section (1) to...Ch. 5 - What is irreversible head loss? How is it related...Ch. 5 - What is useful pump head? How is it related to the...Ch. 5 - Consider the steady adiabatic flow of an...Ch. 5 - Consider the steady adiabatic flow of an...Ch. 5 - What is the kinetic energy correction factor? Is...Ch. 5 - The water level in a tank is 20 m above the...Ch. 5 - A 3-rn-high tank filled with water has a discharge...Ch. 5 - A person is filling a knee-high bucket with water...Ch. 5 - Tater is being pumped from a large lake to a...Ch. 5 - A 15-hp (shaft) pump is used to raise water to a...Ch. 5 - Water flows at a rate of 0.040 m3/s in a...Ch. 5 - The water level in a tank is 20 m above the...Ch. 5 - A hydraulic turbine has 50 m of head available at...Ch. 5 - In a hydroelectric power plant, water flows from...Ch. 5 - Reconsider Prob. 5-78E. Determine the flow rate of...Ch. 5 - A fan is to be selected to ventilate a bathroom...Ch. 5 - Water flows at a rate of 20 L/s through a...Ch. 5 - The water level in a tank is 34 ft above the...Ch. 5 - A large tank is initially filled with water 4 m...Ch. 5 - Water enters a hydraulic turbine through a...Ch. 5 - A 78-percent efficient 12-hp pump is pumping water...Ch. 5 - Water is pumped from a lower reservoir to a higher...Ch. 5 - Water in a partially filled large tank is to be...Ch. 5 - Underground water is to be pumped by a 78 percent...Ch. 5 - Reconsider Prob. 5-88. Determine the flow rate of...Ch. 5 - The velocity profile for turbulent flow in a...Ch. 5 - The demand for electric power is usually much...Ch. 5 - Prob. 92PCh. 5 - Consider a fully filled hemisphere shaped tank...Ch. 5 - The velocity of a liquid flowing in a circular...Ch. 5 - Air at 250 kgrn3 enters a nozzle that has an...Ch. 5 - The air in a 5m5-m3-m hospital room is to be...Ch. 5 - The water level in a tank is 70 ft above the...Ch. 5 - A pressurized 2-rn-diameter tank of water has a...Ch. 5 - Underground water is being pumped into a pool...Ch. 5 - Prob. 100PCh. 5 - A very large tank contains air at 102 kPa at a...Ch. 5 - Water is flowing through a Venturi meter whose...Ch. 5 - Water flows at a rate of 0.011 m3/s in a...Ch. 5 - Air flows through a pipe at a rate of 120 L/s. The...Ch. 5 - A 3-rn-high large tank is initially filled with...Ch. 5 - Reconsider Prob. 5-105. In order to dram the tank...Ch. 5 - A D0= 1 2-rn-diameter tank is initially filled...Ch. 5 - An oil pump is drawing 18 kW of electric power...Ch. 5 - A wind tunnel draws atmospheric air at 20°C and...Ch. 5 - Consider a spherical tank containing compressed...Ch. 5 - A tank with openings 1,2, and 3 is moving to left...Ch. 5 - Two dimensionally identical containers are...Ch. 5 - A circular thin plate is placed on the top of a...Ch. 5 - A pump-storage plant uses a turbine to generate...Ch. 5 - A diffuser in a pipe flow is basically a slow...Ch. 5 - Prob. 117PCh. 5 - Prob. 118PCh. 5 - Prob. 119PCh. 5 - Air enters a steady-flow compressor at 1 atm and...Ch. 5 - A 7$-m-high water body that is open to the...Ch. 5 - Prob. 122PCh. 5 - Prob. 123PCh. 5 - A hydraulic turbine is used to generate power by...Ch. 5 - The efficiency of a hydraulic turbine-generator...Ch. 5 - Which one is not an assumption involved with the...Ch. 5 - Consider incompressible, frictionless flow of a...Ch. 5 - Consider incompressible, frictionless flow of...Ch. 5 - Consider water flow in a piping network. The...Ch. 5 - The static and stagnation pressures of a fluid in...Ch. 5 - The static and stagnation pressures of a fluid in...Ch. 5 - The difference between the heights of energy grade...Ch. 5 - Water at 120 kPa (gage) is flowing in a horizontal...Ch. 5 - Water is withdrawn a the bottom of a large tank...Ch. 5 - Water at 80 kPa (gage) enters a horizontal pipe at...Ch. 5 - Liquid ethanol (p = 783 kg/m3) at a pressure of...Ch. 5 - Seawater is to be pumped into a large tank at a...Ch. 5 - An adiabatic pump is used to increase the pressure...Ch. 5 - The shaft power from a 90 percent-efficient...Ch. 5 - Using a 1are bucket whose volume is known and...Ch. 5 - Your company is setting up an experiment that...Ch. 5 - Computer-aided designs, the use of better...Ch. 5 - Using a handheld bicycle pump to generate an air...Ch. 5 - Using a flexible drinking straw and a ruler,...Ch. 5 - The power generated by a wind turbine is...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- During a trip to the beach (Patm = 101 kPa), a car runs out of gasoline (density is 750 kg/m^3), and it becomes necessary to siphon gas out of another nearby car to a tank of a volume of 4 litres using a hose whose cross-sectional area is 0.2 cm^2. The shown setting is used where L1=0.7 m and L2=2.2 m. Consider point 1 to be at the free surface of gasoline in the tank so that P_1= 1 atm, V_1 ~= 0 since the tank is large relative to the tube diameter. Consider the gravitational acceleration to be 9.81 m/s^2. Using Bernoulli equation, the pressure at point_3 in kPa is: Select one: O a. 72.55 Z3 Ob. 122.34 Gasoline OC. 79.66 siphoning tube L2 Gas tank L1 22 Gas can/arrow_forwardThe pressure in a section of horizontal pipe with a diameter of 2 cm is 152 kPa. Water flows through the pipe at 2.80 L/ s. If the pressure at a certain point is to be reduced to 109 kPa by constricting a section of the pipe, what should the diameter of the constricted section be? Assume laminar nonviscous flow. Express your answer in meters to four decimal places. Us the continuity equation and water flow rate to find the speed of the fluid in one region.arrow_forwardA capillary tube has an 8mm inside diameter through which liquid fluorine refrigerant R-11 flows at a rate of 0.03 cm3/s. The tube isto be used as a throttling device in an air conditioning unit. A model of this flow is constructed by using a pipe of 3cm inside diameter and water as the fluid medium. (Density of R-11 = 1.494 g/cm3 and its viscosity is 4.2 x10-4 Pa.s; Density of water is 1g/cm3 and its viscosity 8.9 x10-4 Pa.s)a) What is the required velocity in the model for dynamic similarity? Hint: For flow through a tube the Ne number can be expressed in terms of the Reynolds numberb) When dynamic similarity is achieved the pressure drop is measured at 50 Pa. What is the corresponding pressure drop in the capillary tube?Hint: In this case the Euler number defines dynamic similarity with reference to the static pressure droparrow_forward
- could you please help me calculate theheigth in metres of the fluid at time t= 100sarrow_forwardConsider the following figure showing a jet of water supporting a weight of 100 N at a height of 5 m. Water leaves the nozzle with a velocity of 20 m/s. The diameter d of the nozzle will be: 100 N 5 m d Nozzle 20 m/sarrow_forwardA cylinder with a mass 0.222 kg is sliding downwards through a vertically positioned pipe. A thin oil layer exists between the cylinder and the pipe's internal surface. Centerline of the cylinder and the pipe overlap. (yoil =8044.2 N /m3 ; voil=6-106 m²/s). Find the change in the speed of cylinder in the pipe with respect to its unit displacement and the shear stress that acts upon the oil layer. A A L = 128 mm V W 73.8 mm 74 mm 0.1 mm Figure 1arrow_forward
- (a) Show, using Bernoulli's theorem, that if there is a hole in the wall of a vessel and if the surface of the liquid inside the vessel is at a height h, above the hole, the velocity of the liquid flowing through the hole is v, = v2gh, (b) Consider a cylindrical vessel having a diameter of 0.1m and a height of 0.2m. A hole 1 cm² in cross-section is opened at the base. Water is flowing into the vessel at a rate of 1.4 x 10* m² s '. (i) Determine how high the water level will rise in the vessel. (ii) After reaching that height the flow of water in the vessel is stopped. Determine the time required for the vessel to empty.arrow_forwardFluid mechanicsarrow_forwardWater is flowing in a 3-cm-diameter garden hose at a rate of 25 L/min. A 20-cm nozzle is attached to the hose which decreases the diameter to 1.2 cm. The magnitude of the acceleration of a fluid particle moving down the centerline of the nozzle is (a) 9.81 m/s2 (b) 17.3 m/s2 (c) 28.6 m/s2 (d ) 33.1 m/s2 (e) 42.4 m/s2arrow_forward
- Question 2: A fluid with density 1 kg/m' is moving through a pipe with same cross-sectional area at a velocity of 1.2 m/s at pointl and 1.5 m/s at point 2, and point 2 above point 1 in the elevation with 3 cm. If the pressure at the beginning at point lis 116 Pa, what is the pressure of fluid at point 2? What is the mass and volume flow rate at point 2? 2 1arrow_forwardThe velocity profile of a liquid flows through the z direction of the vertical tube (figure right) with the radius n is given as; 1 dp (r2 – r3) 2µ dz Vz Specify the max imum velocity and derive an expression for the average velocity.arrow_forwardAn incompressible fluid (density 1000kg/m3) is flowing through a pipe with a constriction. The pipe is on an angle of 30 degrees with the narrow section at at distance of 10m from the wide section and lower that the wide section . The speed of the fluid in the wide section is 2m/s and 10m/s in the narrow section, I f the pressure in the wide section in 250 kPa. What is the pressure of the fluid in the narrow section ?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License