Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 49, Problem 9RQ
To determine
The term tracking as it applies to vehicle handling.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Describe the two basic types of passenger weightdetection sensors used in most vehicles
Explain the five requirements for a car to be automatic:
1. Self drive assistance
2. Semi-automatic steering
3. Auto pilot mode
4. Robotics of the car motion
5. Safety measures (air bags)
Consider one of the advanced driver assistance system(ADAS) called
as adaptive cruise control(ACC). This system is designed for following
a safe distance with front the vehicle. Answer the following questions.
Chapter 49 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 49 - Define camber.Ch. 49 - What tire wear pattern will result from excessive...Ch. 49 - What can be caused by excessive negative caster?Ch. 49 - Describe the difference between toe-in and...Ch. 49 - Describe thrust angle and why it is important foi...Ch. 49 - What can cause incorrect toe-out-on-turns?Ch. 49 - In what direction must the bottom of a tire and...Ch. 49 - What is scrub radius and why is it important?Ch. 49 - Prob. 9RQCh. 49 - Describe how caster adjustment may be used to com...
Ch. 49 - Which of the following is a good definition of...Ch. 49 - Prob. 12RQCh. 49 - A 3-degree difference in the SAI angle on each...Ch. 49 - Unequal SAI angles on the left and right sides of...Ch. 49 - While driving straight, a FWD car pulls to the...Ch. 49 - Technician A says that negative caster provides...Ch. 49 - Technician A says that the purpose of the steering...Ch. 49 - Technician A says that the presence of a thrust...Ch. 49 - Technician A says that camber changes as the...Ch. 49 - Technician A says that caster can be adjusted on...Ch. 49 - Technician A says that on FWD vehicles, the front...Ch. 49 - Technician A says that if caster at both wheels is...Ch. 49 - While discussing front-wheel caster: Technician A...Ch. 49 - While performing a prealignment inspection:...Ch. 49 - While performing a prealignment inspection:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Name the three main driveline components that are added to a RWD vehicle to make it a 4WD vehicle.arrow_forwardDescribe the two basic types of passenger weight detection sensors used in most vehicles.arrow_forwardd) Figure 1 below shows a vehicle which has taken a curve at very high speed, but since the road was slippery, the rear of the car swings to one side. With an aid of sketch, explain what condition it is and how Electronic Stability Programme will act on the vehicle without braking applied condition. Figure 1arrow_forward
- Rack and pinion steering —. a. is lighter in weight and has fewer components than parallelogram steering b. does not provide as much feel for the road as parallelogram steering c. does not use tie-rods in the same fashion as parallelogram steering d. all of the abovearrow_forwardExplain about sensors using for speed, throttle position and crank shaft position with the help of neat diagram.arrow_forwardTechnician A says that on FWD vehicles, the front wheels toe-out while the rear wheels on an independent suspension try to toe-in as the vehicle moves ahead. Technician B says that on RWD vehicles, the front wheels tend to toe-in while the rear wheels toe-out in response to rolling resistance as suspension compliance. Who is correct?arrow_forward
- Technician A says that throttle position is an important input in most electronic shift control systems. Technician B says that vehicle speed is an important input for most electronic shift control systems. Who is correct?arrow_forwardDescribe at least two methods of checking the operation of Hall-effect sensors used in engine management systems. (40 - 60 words)arrow_forwardA 3-degree difference in the SAI angle on each side of the front suspension may cause a FWD vehicle to have increased during hard acceleration.arrow_forward
- List the various methods used by traction control systems to eliminate wheel spin.arrow_forwardDefine the difference between an integrated and anonintegrated antilock braking system.arrow_forwardA computer is capable of doing all of the following except___.a. receive input datab. process input data according to a programand monitor output actionc. control the vehicle’s operating conditionsd. store data and informationarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,