Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 46, Problem 7ASRQ
When the front wheels are turned on a vehicle equipped with front struts, the left front coil spring provides a chattering action and noise: Technician A says that the strut has internal defects and strut replacement is necessary Technician B says that the upper strut bearing and mount are defective. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Hello, I am trying to study for a test and found this practice review but I'd like to be able to check my work. Can someone help answer some of these questions? Thank you
When reviewing the service procedures for CV joints and drive axles,
Technician A says that the axle can be used as a slide hammer to help remove a stubborn inboard joint from the transaxle.
Technician B says that a drive axle should never be allowed to hang by its own weight during removal or installation.
Who is correct?
O a. A only
Ob.B only
O c. Both A and B
O d. Neither A nor B
Question 4
i put D and it was incorrect
Chapter 46 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 46 - Prob. 1RQCh. 46 - Explain the difference between sprung and unsprung...Ch. 46 - What are two reasons for using an air spring?Ch. 46 - Explain the action of the conventional shock...Ch. 46 - Prob. 5RQCh. 46 - Prob. 6RQCh. 46 - What occurs when a wheel hits a dip or hole and...Ch. 46 - Which of the following is part of the sprung...Ch. 46 - What occurs when a wheel hits a dip or hole and...Ch. 46 - Describe the common complaints caused by faulty...
Ch. 46 - The modified MacPherson rear strut suspension is...Ch. 46 - What controls the movement of a vehicle as it...Ch. 46 - The coil springs of the vehicle_. a. support the...Ch. 46 - The two SLA systems in common use today are the...Ch. 46 - A multilink front suspension contains which of the...Ch. 46 - Technician A says that the use of firmer, urethane...Ch. 46 - Prob. 2ASRQCh. 46 - Technician A says that a weak suspension spring...Ch. 46 - Technician A says that leaf spring-type rear...Ch. 46 - Technician A says that shock absorbers should be...Ch. 46 - While discussing types of coil springs: Technician...Ch. 46 - When the front wheels are turned on a vehicle...Ch. 46 - Technician A says that the suspension switch must...Ch. 46 - While conducting a bounce test: Technician A says...Ch. 46 - Technician A says that rattling on road...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that leaf spring type suspensions are subject to wheel tramp. Technician B says that anti sway bars are designed to limit wheel tramp. Who is correct?arrow_forwardA multilink front suspension contains which of the following? a. Strut b. Control arms c. Ball joints d. All of the abovearrow_forwardExplain the difference between sprung and unsprung weight.arrow_forward
- When reviewing the procedure for replacing an axle boot, Technician A says that the position of the old boot should be marked on the shaft before removing it. Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardThe worm wheel rim is made of copper forA.Easy to manufacture B.Stable transmissionC.High precision D.Wear reductionarrow_forwardWhen the clutch is disengauged, where does the power flow stop? Select one: a. the transmission input shaft b. the driven hub c. the pressure plate and flywheel d. the torsion springsarrow_forward
- When discussing CV joint diagnosis, Technician A says that the complete failure of a CV joint may cause the vehicle not to hold in Park. Technician B says that a worn axle dampener assembly can cause a vibration while driving. Who is correct? O a. A only O b. B only c. Both A and B O d. Neither A nor Barrow_forwardThe modified MacPherson rear strut suspension is common in _______. a. FWD vehicles b. RWD vehicles c. pickup trucks d. station wagonsarrow_forwardWhat type of ball joint is used on the lower control arm of an SLA suspension when the coil spring is placed between the lower control arm and the frame, and the control arm is beneath the knuckle?arrow_forward
- From the following identify a true statement regarding the adjustment of drive belt tension. а. More than 6 mm should be the correct a deflection for each belt which is under tension O b. More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension. c. More than 8 mm should be the correct a deflection for each belt which is under tension. O d. Less than 8 mm should be the correct a deflection for each belt which is under tensionarrow_forwardWhat is benefit of bifilar suspension technique?arrow_forwardFrom the following identify a true statement regarding the adjustment of drive belt tension. a. Less than 8 mm should be the correct a deflection for each belt which is under tension b. More than 6 mm should be the correct a deflection for each belt which is under tension c. More than 8 mm should be the correct a deflection for each belt which is under tension. d. More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License