Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 46, Problem 5MC
What is used to control the movement of a vehicle as it goes around corners?
a. Struts
b. Shock absorbers
c. Stabilizer bar
d. Control arms
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Number 5 I put B but it was incorrect
While conducting a bounce test: Technician A says that the bumper should be pushed two or three times downward with considerable weight applied on each corner of the vehicle. The bumper should be released after each push and the vehicle should oscillate about 1½ cycles and then settle. Technician B says that one free upward bounce should stop the vertical chassis movement if the shock absorber or strut provides proper spring control. If the vehicle’s bumper does more than 1½ free upward bounces, the shock absorber or strut is defective. Who is correct?
Is number 11 right
Chapter 46 Solutions
Automotive Technology
Ch. 46 - Prob. 1SACh. 46 - Explain the difference between sprung and unsprung...Ch. 46 - What are two reasons for using an air spring?Ch. 46 - Explain the action of the conventional shock...Ch. 46 - Prob. 5SACh. 46 - Describe the common complaints caused by faulty...Ch. 46 - Prob. 7SACh. 46 - What occurs when a wheel hits a dip or hole and...Ch. 46 - Which of the following is part of the sprung...Ch. 46 - What occurs when a wheel hits a dip or hole and...
Ch. 46 - The modified MacPherson rear strut suspension is...Ch. 46 - What is used to control the movement of a vehicle...Ch. 46 - The coil springs of the vehicle_. a. support the...Ch. 46 - SLA systems in common use today are used in the...Ch. 46 - A multilink front suspension contains which of the...Ch. 46 - Technician A says that the use of firmer, urethane...Ch. 46 - Prob. 2ASRQCh. 46 - Technician A says that a weak suspension spring...Ch. 46 - Technician A says that leaf spring-type rear...Ch. 46 - Technician A says that shock absorbers should be...Ch. 46 - While discussing types of coil springs: Technician...Ch. 46 - When the front wheels are turned on a vehicle...Ch. 46 - Technician A says that the suspension switch must...Ch. 46 - While conducting a bounce test: Technician A says...Ch. 46 - Technician A says that rattling on road...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The modified MacPherson rear strut suspension is common in _______. a. FWD vehicles b. RWD vehicles c. pickup trucks d. station wagonsarrow_forwardIn front-wheel drivetrains, the CV joint nearer the transaxle is the____. a. inner joint b. inboard joint c. outboard joint d. both a and barrow_forwardWhile conducting a bounce test: Technician A says that the bumper should be pushed two or three times downward with considerable weight applied on each corner of the vehicle. Technician B says that one free upward bounce should stop the vertical chassis movement if the shock absorber or strut provides proper spring control. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- The two SLA systems in common use today are the ________. a. coil spring and strut suspension b. coil spring and torsion bar suspension c. coil spring and single control arm suspension d. single and double control arm suspensionarrow_forwardTRUE OR FALSE1. The primary and secondary suspensions are designed to achieve very poor ride quality, not safe performance during curve negotiation and bad dynamic behavior on a tangent track. 2. Each bogie frame is connected to car body through side bearings. 3. the wheel sets are located within a frame, either a bogie or directly in the vehicle, and are restrained by a large yaw stiffness. 4. When considering maintenance for railways, often the consequences can easily be changed. 5. Maintenance can only have positive effects. 6. Corrective maintenance also called as down systems. 7. the disadvantage of this system is the relatively low frequency of maintenance.arrow_forwardHello, Can someone help answer these questions about suspension systems? Thank youarrow_forward
- Dry friction: O Produces a force normal to the surfaces of contact. Occurs only when two objects are moving past each other. Occurs when objects are in a condition of sliding or a tendency to slide. O Occurs only when two objects are in a condition of a tendency to slide.arrow_forwardHello, I am trying to study for a test and found this practice review but I'd like to be able to check my work. Can someone help answer some of these questions? Thank youarrow_forwardA multilink front suspension contains which of the following? a. Strut b. Control arms c. Ball joints d. All of the abovearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Column buckling; Author: Amber Book;https://www.youtube.com/watch?v=AvvaCi_Nn94;License: Standard Youtube License