Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 46, Problem 5ASRQ
Technician A says that shock absorbers should be inspected for loose mounting bolts and worn mounting bushings. Technician B says that shock absorbers and struts should be inspected for oil leakage. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A discussion concerning CV joint testing is being held.
Technician A says that a recommended method to check CV joints is to raise the vehícle so that the lower control arms are hanging freely; at this point the engine can be
accelerated while noise checks can be performed.
Technician B says that the vehicle should be road tested so that the CV joints can be checked under load.
Who is correct?
O a. A only
O b. B only
c. Both A and B
d. Neither A nor B
The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart.
Technician A says that one or more of the engine/transaxle's mounts may be broken.
Technician B says that one or more of the engine/transaxle's subframe mounts may be broken.
Who is correct?
O a. A only
O b.B only
C. Both A and B
O d. Neither A nor B
Technician A says a sticking inboard joint can cause the car to shimmy during acceleration.
Technician B says a worn inboard joint can cause a clunking during acceleration and deceleration.
Who is correct?
O a. A only
O b. B only
O c. Both A and B
O d. Neither A nor B
Chapter 46 Solutions
Automotive Technology
Ch. 46 - Prob. 1SACh. 46 - Explain the difference between sprung and unsprung...Ch. 46 - What are two reasons for using an air spring?Ch. 46 - Explain the action of the conventional shock...Ch. 46 - Prob. 5SACh. 46 - Describe the common complaints caused by faulty...Ch. 46 - Prob. 7SACh. 46 - What occurs when a wheel hits a dip or hole and...Ch. 46 - Which of the following is part of the sprung...Ch. 46 - What occurs when a wheel hits a dip or hole and...
Ch. 46 - The modified MacPherson rear strut suspension is...Ch. 46 - What is used to control the movement of a vehicle...Ch. 46 - The coil springs of the vehicle_. a. support the...Ch. 46 - SLA systems in common use today are used in the...Ch. 46 - A multilink front suspension contains which of the...Ch. 46 - Technician A says that the use of firmer, urethane...Ch. 46 - Prob. 2ASRQCh. 46 - Technician A says that a weak suspension spring...Ch. 46 - Technician A says that leaf spring-type rear...Ch. 46 - Technician A says that shock absorbers should be...Ch. 46 - While discussing types of coil springs: Technician...Ch. 46 - When the front wheels are turned on a vehicle...Ch. 46 - Technician A says that the suspension switch must...Ch. 46 - While conducting a bounce test: Technician A says...Ch. 46 - Technician A says that rattling on road...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that coolant hoses should be squeezed to check for hardening or softening. Technician B says that coolant hoses should be visually inspected for swelling and cracks. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardRoad test Report is Overhaul all four-wheel brakes and the Universal joints After the maintenance operation is completed, the road test inspector or the machine creates the road test report In case of diesel engines overhaul injectors, besides the above items of wash, all the items mentioned in the monthly maintenance schedule should be carried out during quarterly maintenance also. During service, remove and clean shackle pin if necessary Skiparrow_forwardA vehicle has had several radiator replacements, and each time there has been pinhole leaks in the aluminum. Technician A states that the engine coolant may need to be exchanged more often. Technician B states that the engine grounds should be inspected closely since this could be the cause. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forward
- Technician A says that the piston seal retracts the caliper piston when hydraulic pressure is released. Technician B says that a return spring is used to retract a caliper piston. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhen examining disc brakes: Technician A visually inspects the rotor and says that the rotor can be reused if it is not damaged or scored. Technician B says that it is normal for the inboard pad to be slightly more worn than the outside pad. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following statements about drum brakeshoes is not true?a. Web thickness varies only with changes in shoesize.b. Many shoes have indented places along the edgeof the rim.c. The shoe rim is welded to the web.d. The primary/leading shoe is typically the one thatis positioned toward the front of the vehiclearrow_forward
- explain the action of the conventional shock absorber on both compression (jouce) and rebound strokesarrow_forwardAfter resurfacing a brake drum: Technician A cleansit using hot water and a lint-free cloth. He then usescompressed air to thoroughly dry it. Technician Bcleans the drum using a lint-free cloth dipped in aspecial brake cleaning solvent. She then allows thedrum to dry before reinstallation. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forwardWhich of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc. Engined. All of the abovearrow_forward
- Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the system. Technician B says that a loss of hydraulic fluid or power booster pressure disables the antilock brake system. Who is correct? a. Technician A only b.Technician B only c.Both A and B d.Neither A nor Barrow_forwardWhen discussing CV joint diagnosis, Technician A says that the complete failure of a CV joint may cause the vehicle not to hold in Park. Technician B says that a worn axle dampener assembly can cause a vibration while driving. Who is correct? O a. A only O b. B only c. Both A and B O d. Neither A nor Barrow_forwardA vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced. Technician A says that the left inner CV joint may be the source of the noise. Technician B says that the left outer CV joint may be causing the noise. Who is correct? O a. A only Ob.B only O c. Both A and B O d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License